Friday, June 13, 2014

Maytag FAV6800 One Way Clutch vs One Way Bearing video



Washer Tub Bearings - Here is a video that compares the one way clutch to the special one way bearing. Your FAV6800 washer will have one or the other. You can replace your bearings and tub seal when they start to get loud.

It was believed that you could go by the first two digits of your serial number to determine if you had the special bearing or one way clutch. However, experience tells me otherwise and that is why I created this video for you.

There are two kits for you to choose from depending on if you have the one way clutch or the one way bearing. Watch the video...


If you need other appliance parts you can visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal and enter your model and see what they can do for you.

Leave your comments below and share with your family and friends that may have clothes washers so they will be aware that they can replace their bearings and tub seal and save a ton of money!


Jeff Hartman

Wednesday, June 4, 2014

MAH7500AWW Bearing and Tub Seal – How To Replace them and save money

MAH7500AWW Bearing and Tub Seal – How To Replace them and save money

If you own a MAH7500 and it sounds like a jet plane then it is time to focus on your bearings and tub seal. If you bother a Maytag service technician they will want at least $950 to repair your Neptune or even suggest that you junk machine. You don’t really want to scrap machine because you can save money by replacing your Neptune bearings and tub seal and be washing clothes again. The reason they quote so much is because they will want to replace the large outer tub which runs over $500 alone!

The 12002022 seal kit contains two seals. The earlier lip seal and the revised lip seal. If you have the earlier lip seal (with plastic white spacer clip) you will need to replace it with the new earlier lip seal in the kit. If you would like to use the revised lip seal you will have to purchase a new spinner support because its’ shaft is machined different. Here is a video I created for the 12002022 seal kit breakdown.

It should take about 1 – 5 hours depending on how much cleaning you need to do while you’re in there and no special tools are required. You could save time by renting the Tony Tool which pulls the rear bearing out first. You then knock the front bearing out and then after some clean up you use the Tony Tool to install the new bearings and spacer. The tool kit rental includes an extra bearing spacer just in case you need it.

Depending on how long your machine has sounded like a jet plane you may need to heat up the aluminum hub when extracting the inner or front bearing. The aluminum has a higher expansion coefficient than the steel bearing does so the bearing housing should expand more than the bearing does thus loosening it up. Just don’t over heat it since some of the heat guns can really get hot.

Another tip is to stabilize the outer tub by laying the Neptune on its front and placing 2x4’s, old towels, newspaper stack under tub to help keep it from bouncing around when you attempt to knock out the front bearing. Now would also be a good time to spray penetrating oil on the inner bearing since it is closer to horizontal. You can allow the oil to soak in overnight. You will also want to place plywood or equivalent under tub to catch the bearing when it is ejected out.

The good news is that you don’t have the faulty brown tipped wax motor in your door latch. Only the timer knob based Neptune’s have the wax motor which would fail and damage the Q6 triac and R11 and the upper control board. The digital Neptune models all use a solenoid to lock the door. See Neptune Help Song for a video that explains what happens when the original brown tipped wax motor fails. 

I hope this was helpful to you and you save money by replacing your bearings and tub seal.  

Leave your comments below...

               


Monday, June 2, 2014

MAH6500AWW Bearing and Tub Seal – How To Replace







If you own a MAH6500 and it sounds like a freight train it is time to replace your bearings. If you bother Ole’ Lonely he will quote you at least $950 or suggest that you scrap machine. You don’t want to scrap machine because you can save money by replacing your Neptune tub bearings and seal and be washing clothes soon. Ole’ Lonely will want to replace your large outer tub which runs over $500 alone! You don’t need to replace the expensive outer tub.

There are two seals that are available in the genuine 12002022 seal kit. The earlier lip seal and the revised lip seal. If you have the earlier lip seal (with plastic white spacer clip) you will need to replace it with the new earlier lip seal in the kit. If you would like to install the revised lip seal you will have to replace your W10181639 spinner support because its shaft is machined different.

It should take about 1 – 4 hours depending on how much cleaning you need to do while you’re in there and no special tools are required. You could save time by renting the Tony Tool which pulls the rear bearing out first. You then knock the front bearing out and then after some clean up you use the Tony Tool to install the new bearings and spacer. The tool kit rental includes an extra bearing spacer just in case you need it. The Maytag Neptune Bearing and 12002022 Seal kit also includes an ebook with more information and tips to help you be successful.

Depending on how long your machine has sounded like a jet plane you may need to heat up the aluminum hub when extracting the inner or front bearing. The aluminum has a higher expansion coefficient than the steel bearing does so the bearing housing should expand more than the bearing does thus loosening it up. Just don’t over heat it since some of the heat guns can really get hot.

The good news is that you don’t have the faulty brown tipped wax motor in your door latch. Only the timer knob based Neptune’s have the wax motor which would fail and damage the Q6 triac and R11 and the upper control board. See Neptune Help for more wax motor information. The digital Neptune models all use a solenoid to lock the door.

I hope this was helpful to you. 

Please leave any comments below.

Jeff Hartman


  

               

Monday, May 19, 2014

Online Safety Videos - Your Step By Step Safety Implementation Plan




http://www.onlinesafetyvideos.com – Is where your small company can learn step by step how to implement an OSHA compliant safety program. Don’t wait until OSHA is at your door to think about starting your safety program because it will be tool late then!
OSHA loves visiting companies that do not have a safety program in place because they will have a field day with fines… Get your safety program started now! 

Our team will help you along the way via step by step program which starts with how to access a top notch online safety video provider for only $450 a year where it normally runs > $900.

Once you have access you will discover how easy it is to create your written safety plans. As a matter of fact… You simply can fill in the blanks, print and file in a 3 ring binder! In addition, there are videos that are updated when OSHA makes regulation changes so you know your employees are up to date. Don’t take chances with the free safety videos floating around on the web.

Take advantage of our introductory rate and lock your rate in for the future as well.


Here are some businesses that will benefit from starting a safety program:

Doctor/Dentist office

Chiropractor Office

Any Contractors/Construction

Restaurant/Kitchen

Manufacturing

Welding

Machine Shop

Paint Shop

Printing Shop

Courier/Transportation

Laboratory

Maintenance

Warehouse

Landscaping

Office

Pest Control

Agriculture

Laundromat


Please contact me if you have any questions. For more information see http://www.onlinesafetyvideos.com 


Online Safety Video team

Tuesday, May 13, 2014

Whirlpool Duet Bearing – How To Replace



Whirlpool Duet Bearing – How To Replace

If your Whirlpool Duet front load washer sounds like a freight train then it is time to derail your Duet and replace the tub seal and bearings. The duet bearing replacement process is pretty straight forward and no special tools are required. See Whirlpool Duet Bearing for the replacement tub bearing and seal kits. Most appliance repair centers will tell you that you have the replace the rear tub but that is just not the case…

The bearing Kits include an eBook that will give you tips on bearing replacements as well as a link to a service manual you can download to help as well. Tell all of your family and friends that you can replace the Whirlpool Duet at www.duetbearing.com.

For more washer bearing and tub seal kits see www.washerbearings.com.



Jeff Hartman

Kenmore Elite HE3 Bearing and Seal Kit – How To



Kenmore Elite HE3 Bearing and Seal Kit – How To


If you own a Kenmore Elite HE3 front load washer and it has morphed into a jet plane… I have great news!  You can replace your bearings and seal and save! I would expect 3 hours for the repair depending on how much cleaning you do while you have the Elite disassembled. You won’t need any special tools to replace the tub seal and bearings. See Elite Bearing for the tub bearing and seal kits. The Elite kit works on the HE3, HE3T, HE4, HE4T, HE5 and HE5T models. If you have the HE2 model you will need this 8540347 bearing and Seal kit.

When you notice the washer getting louder usually in high speed spin mode you will want to take action asap before the rust sets in the bearings. Otherwise, you may have a bearing that hangs up and scores the support bracket shaft. Whirlpool only offers the support brackets along with a new stainless steel basket as an assembly which drives up the cost considerably. If your support bracket shaft is damaged you can repair it by taking it to a machine shop where they can install a sleeve or weld up the area and machine it back down again for the new bearing.

I hope this was helpful.

Leave any comments below.

Jeff Hartman