WFW8400TB00 Bearing and Seal Kit with 8540347 Seal

WFW8400TB00 Bearing and Seal Kit with 8540347 Seal

If you own a Whirlpool WFW8400TB00 washer and it sounds like a jet plane you can replace your bearings and tub seal see http://duetbearing.com/page8.html.

 Other models with different suffixes are WFW8400TB01, WFW8400TB02, WFW8400TE00, WFW8400TE01, WFW8400TW00, WFW8400TW01, WFW8400TW02, WFW8400TW03, WFW8400SR0, WFW8400SR01, WFW8400SR02, WFW8400SR03 and WFW8400SR04. No special tools are required.

The typical process is to disassemble the machine to pull the large outer tub out. Some brave souls pull it without removing the three counter weights. I prefer to pull the counter weights to make it more manageable. Once the outer tub is out you can remove the clips and split the tub into two halves. Once the front half is off you can pull the stainless steel basket out which will expose the 8540347 tub seal.

You can remove the 8540347 seal and check the rear bearing for a snap ring or retainer clip. If so, remove the clip so you can tap out the rear bearing first working through the front bearing bore. Once the bearings are out you can do some housework to prepare it for reception of the new bearings.

When tapping in the bearings take care not to impact the inner race so you don’t bruise the new bearing which can cause bearing to be noisy as well as premature bearing failure. Some clients use a socket extension and hammer to tap in the new bearings carefully keeping the impact on the outer race only.

Once new bearings are fully set you can then install the new 8540347 seal. Finally, put here all back together again and perform a test run and watch for leaks.

I hope this helps you understand what is involved when replacing your WFW8400TB00 tub bearings and 8540347 seal. See http://duetbearing.com/page8.html for your replacement bearing and 8540347 seal.

                                                                                                                                 

Jeff Hartman

"The Neptune Man"

WFW8410SW0 Bearing and Seal Kit with 8540347 Seal

WFW8410SW0 Bearing and Seal Kit with 8540347 Seal

If you own a Whirlpool WFW8410SW0 washer and it sounds like a jet plane you can replace your bearings and tub seal see http://duetbearing.com/page8.html for your bearing and seal kit . No special tools are required. Other model suffixes could be WFW8410SW01, WFW8410SW02, WFW8410SW03.

The typical process is to disassemble the machine to pull the large outer tub out. Some brave souls pull it without removing the three counter weights. I prefer to pull the counter weights to make it more manageable. Once the outer tub is out you can remove the clips and split the tub into two halves. Don't forget to mark where the clips are for when you're putting it all back together. Once the front half is off you can pull the stainless steel basket out which will expose the 8540347 tub seal.

You can remove the 8540347 seal and check the rear bearing for a snap ring or retainer clip. If so, remove the clip so you can tap out the rear bearing first working through the front bearing bore. Once the bearings are out you can do some housework to prepare it for reception of the new bearings.

When tapping in the bearings take care not to impact the inner race so you don’t bruise the new bearing which can cause bearing to be noisy as well as premature bearing failure. Some clients use a socket extension and hammer to tap in the new bearings carefully keeping the impact on the outer race only.

Once new bearings are fully set you can then install the new 8540347 seal. Finally, put here all back together again and perform a test run and watch for leaks.

I hope this helps you understand what is involved when replacing your WFW8410SW0 tub bearings and 8540347 seal. See http://duetbearing.com/page8.html  to order your replacement bearing and tub seal kit.

For other appliance parts visit www.washerbearings.com/parts

                                  

                                                                                               

Jeff Hartman

"The Neptune Man"

Whirlpool Duet Bearing – How To Replace

Whirlpool Duet Bearing – How To Replace

If your Whirlpool Duet front load washer sounds like a freight train then it is time to derail your Duet and replace the tub seal and bearings. The duet bearing replacement process is pretty straight forward and no special tools are required. See Whirlpool Duet Bearing for the replacement tub bearing and seal kits. Most appliance repair centers will tell you that you have the replace the rear tub but that is just not the case…

The bearing Kits include an eBook that will give you tips on bearing replacements as well as a link to a service manual you can download to help as well. Tell all of your family and friends that you can replace the Whirlpool Duet at www.duetbearing.com.

For more washer bearing and tub seal kits see www.washerbearings.com.

Jeff Hartman

Whirlpool Duet Bearing Replacement

Whirlpool Duet Bearings and seal kits are now available!

Since I have been helping Maytag Neptune front load washer owners save hundreds of thousands of dollars on Maytag Neptune Parts it is time to help the Whirlrpool Duet front load washer owners save too!

Duet owners can now purchase the replacement bearings and seal for their Duet washers at Duet Bearing.

I can also get you a quote for any part for the Duets as well... Just send me an email with the part number, if you have it, and I will save you even more money!

If you know anyone with a Duet front load washer please pass this information along to them so they can save money on their washer repair.

Until next time...