110.73012101 Kenmore Elite dryer not heating, gas dryer no heat, how to fix a dryer

Appliance Parts - My friend was having a dryer issue where it would not dry the clothes or it was taking longer to dry so I stopped by to take a look at it. I went ahead and brought a replacement gas dryer ignitor or hot surface ignitor (HSI) with me because that is a common part to fail since they thermally cycle in their normal operation and eventually wear out. This particular dryer had the lower kick panel so I can remove it and have a good view of the gas valve assembly. When I was there watching it… of course it worked without failure.

About a week later they called again so I stopped by and took another look. When I first started up dryer the HSI ignitor glowed and the gas valve clicked and she fired up. I waited until the gas valve shut off and wanted to see if it would relight properly. It turns out… it lit properly sometimes and sometimes not. Knowing that the common dryer problems are the ignitor and coils on the gas valve I would focus on the coils because the ignitor is glowing just fine.

Next, I ordered the 279834 coil set and changed them out and that was the problem. You can visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal. Have your model number available.

Don’t forget safety when working on appliances. Make sure you unplug the power cord before opening the appliance. When changing the 279834 coils… Be aware that there is a metal sleeve on the post that has the 3 terminal coil on it. Make sure you have that metal sleeve on the post because it can come off with the old coil and remain inside it. That valve post with the 3 terminal coil needs to have the metal sleeve on it to work properly. Don’t lose the metal sleeve because I don’t believe you can order that part and you will probably have to order a new gas valve to get one.

Thanks to this easy and low cost repair we saved another appliance from the grave yard! Tip: I had to use a short stubby Philips screwdriver in order to get the bracket off that clamps the coils down. Otherwise, I would have had to take the machine apart. If you don’t have the separate kick panel on the bottom on your dryer you will have to dive deeper into the dis assembly process to get to the gas valve assembly.

By the way… I measured the new coils and the old coils with an ohmmeter.

New Coil #1 (3 terminal)                              Old Coil #1

1-2 = 2.97K Ohms                                             1-2 = Open

2-3= 3.54K Ohms                                              2-3= Open

1-3= 2.1K Ohms                                                                1-3= 727 Ohms

New Coil #2 (2 terminal)                              Old Coil #2

1-2 = 1.45K ohms                                              1.276K ohms

We can now understand why the dryer was failing to activate the gas valve properly… The old coil with 3 terminals has opened up internally.

I hope this post helped you get your dryer repaired and back in operation with minimal cost and effort.

While you are here… I offer bearing and seal kits for washers at my www.washerbearings.com. If you have a Maytag Neptune, Whirlpool Duet, Kenmore Elite and others you can save big time and keep your machine out of the grave yard and keep more cash in your wallet!

Thank you,

Jeff Hartman

Duet WFW9410XW00 Bearing and Tub Seal

                                               

Duet WFW9410XW00 Bearing and Tub Seal

Whirlpool Duet WFW9410XW00 owners… If your washing machine is sounding like a freight train then you will need to swap your bearings and tub seal. Once you notice it getting louder it is best to quit using it so you don’t cause more damage to machine.

If you happen to damage your Duet’s support bracket (spider) shaft you can remove it from stainless steel inner basket and take it to a machine shop to be repaired. They could install a sleeve or weld up then machine back down to correct diameter for new bearing. If the seal seat on the shaft is damaged then I don’t know of any repairs at this time for those since they are glued to the support bracket shaft.

The WFW9410XW00 bearing replacement is performed without any special tools and you should be able to complete it in 2 - 3 hours. You will need some room to disassemble machine because the tub is large and you will need room to separate it so you can take out the inner basket and support bracket. It also helps to remove the 3 counter weights to make the tub more manageable.

You can order your WFW9410XW00 tub bearings and seal at http://duetbearing.com/page9.html. These kits are shipped via US Priority Mail.

Here are some additional models this kit will work on:

MHWE400WJ00 , MHWE400WJ01 , MHWE400WR00 , MHWE400WR01 , MHWE400WW00 , MHWE400WW01 , MHWE450WJ00 , MHWE450WJ01 , MHWE450WR00 , MHWE450WR01 , MHWE450WW00 , MHWE450WW01 , MHWE550WJ00 , MHWE550WJ01 , MHWE550WR00 , MHWE550WR01 , MHWE550WW00 , MHWE550WW01 , MHWE950WW00 , NFW7600XW00

WFW9410XW00 , WFW9451XW00 , WFW9470WL00 , WFW9470WL01 , WFW9470WR00 WFW9470WR01 , WFW9470WW00 , WFW9470WW01 , WFW9550WL10 , WFW9550WW10 , WFW9630YW00 , WFW9640XW00 , WFW9750WL00 , WFW9750WL01 WFW9750WL02 , WFW9750WR00 , WFW9750WR01 , WFW9750WR02 , WFW9750WW00 WFW9750WW01 , WFW9750WW02

Leave any comments below.

Jeff Hartman

www.washerbearings.com

led lights - Litepods Night light system

led lights

led lights

Here is an led light you can install in your home to light up your hallways and stairs. They are powered by 6 volts and can have a battery backup added for more safety and convenience. You can add up to (40) Litepods Emitters to a system which should cover most homes. These are considered low voltage lighting and night lights. 

To install you simply run 22-2 wire from one location which could be in a closet or basement. That location should have 120 VAC outlet nearby or at least one close enough to run a 22-2 wire to so you can connect to the power supply. When running your wires... you can home run all of the wires from each Litepods Emitter or you can daisy chain them. You can also run a 22-2 wire from your basement to attic then attach to a LPTB board with is a terminal block board so you can connect the Litepods Emitters to the LPTB board. You will drill a 3/4" hole with a paddle bit and you can then pull the wire through. Next, you make your connections with the B connectors. Once you make all of your connections you can then power up the system.

Don't forget to run a 22-2 wire to a widow for the light sensor. You could keep the Litepods on all of the time if you cannot conveniently run a wire for the light sensor since they draw very little power. With the LPLS board you can use a switch, relay or open collector transistor to turn Litepods on and off if you don't want to use the light sensor.

Below is a typical system you would need to get started.

In hallways, I would recommend placing the Litepods Emitters every 3 to 5 feet depending on how much light you would like.

I hope this helped you.

Leave any questions or comments below.

Jeff Hartman

www.litepods.com

P.S. Remember you can order appliance parts by visiting www.washerbearings.com/parts to order replacement parts other than tub bearings and seal.. Have your model number available.

How to change LED in a Litepods Emitter - Nightlights for kids

www.litepods.com - This video demonstrates how easy and quick it is to change an LED in a Litepods Emitter. The LED Emitters normally ship with a white LED installed. You may decide to change the color or go with an RGB LED which changes colors and are cool for nightlights for kids.

These Litepods Emitters are night lights that can be installed in bedroom ceilings near the door to illuminate that area so if they need to get up and go to bathroom in the night they can without turning on any lights. Imagine walking through your house with no lights on and not tripping on children's toys or going to the bathroom in the middle of the night without turning on bright lights that could wake your significant other...

You can install these LED Emitters in the ceiling or along stairs or under cabinets since they are considered low voltage lighting.

Leave any questions or comments below and don't forget to follow me.

Jeff Hartman

P.S. If your washing machine is sounding like a freight train when it is spinning then it sounds like you need to replace your bearings. See washer bearings for information on how to change your tub bearings and seal and save money by repairing it yourself.

Kenmore Elite HE5T Bearing and Tub Seal Replacement

Kenmore Elite HE5T Bearing and Tub Seal Replacement

Kenmore Elite HE5T Bearing and Tub Seal Replacement

Kenmore Elite HE5T owners… If your washing machine is sounding like a freight train then you will need to replace your bearings and tub seal. It is best to stop using machine as soon as you hear it getting louder so you don’t cause further damage to machine.

If you damage your Elite’s support bracket (spider) shaft you can remove it from stainless steel inner basket and take it to a competent machine shop to be repaired. They can install a sleeve or weld up then machine back down to correct diameter for new bearing. If the seal seat on the shaft is damaged then I don’t know of any repairs at this time for those since they are glued to the support bracket shaft.

The Elite tub bearing replacement is performed without any special tools and you should be able to complete it in 2 - 3 hours. You will need some room to disassemble machine because the tub is fairly large and you will need room to split it in two so you can take out the inner basket and support bracket. It helps to remove the three counter weights to make the tub more manageable weight wise.

You can order your Kenmore Elite HE5T Duet tub bearings and seal at http://duetbearing.com/page7.html. These kits are shipped via US Priority Mail. We also offer shipping to other countries as well.

Leave any comments or questions below...

Thank you,

Jeff Hartman

WFW9600TW01 Bearing and Tub Seal Replacement - If washer sounds like a freight train

WFW9600TW01 Bearing and Tub Seal Replacement

Whirlpool Duet WFW9600TW01 owners… If your washing machine is sounding like a freight train then you will need to replace your bearings and tub seal. It is best to stop using machine as soon as you hear it getting louder so you don’t cause further damage to machine.

If you damage your Duet’s support bracket (spider) shaft you can remove it from stainless steel inner basket and take it to a competent machine shop to be repaired. They can install a sleeve or weld up then machine back down to correct diameter for new bearing. If the seal seat on the shaft is damaged then I don’t know of any repairs at this time for those since they are glued to the support bracket shaft.

The Duet tub bearing replacement is performed without any special tools and you should be able to complete it in 2 - 3 hours. You will need some room to disassemble machine because the tub is fairly large and you will need room to split it in two so you can take out the inner basket and support bracket. It helps to remove the three counter weights to make the tub more manageable weight wise.

You can order your WFW9600TW01 Duet tub bearings and seal at http://duetbearing.com/page7.html. These kits are shipped via US Priority Mail.

Leave any comments or questions below.

Thank you,

Jeff Hartman

P.S. You can visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal. Have your model number ready. 

Whirlpool Duet DSS 1 Rear Bearing Kit - How To Replace Your Washer Bearings