Thursday, October 27, 2022

No hot water! Gas water heater burner wont stay lit. Problem Solving. Mo...



How to easily diagnose and repair a faulty gas-fired water heater when the burner lights and then goes out. In this case it was the flame rod causing the issue because the control module was not getting the flame rod signal so it cuts off the gas valve. It will retry for three times then lock out until control module is reset. We cleaned flame rod with a blue sponge with scrubbing side and it worked for a few weeks. This trick could keep your hot water flowing until your replacement ignitor/flame rod arrives… Once it quit working again we knew the ignitor/flame rod assembly needed replaced. We also cleaned the air intake vents, inspected for any water leaks and there was none.

This model is a higher efficiency model because it does not have a pilot light but it does have an inducer fan with plastic exhaust pipe because it utilizes more of the generated heat to actually heat the water and transmits less heat out of the stack. The drawback is that it plugs into a 120VAC outlet to power the control module and inducer fan which is rather loud in my opinion when it is running. The other weakness is that during a power failure you could run out of hot water. The water heater in this video is the A.O. Smith 50 gallon: Model GPSH 50 100.

Here’s a helpful manual: https://www.hotwater.com/lit/im/res_gas/185171-001.pdf See page 13 for troubleshooting chart. Ebay 𝗔𝗳𝗳𝗶𝗹𝗶𝗮𝘁𝗲 𝗟𝗶𝗻𝗸 - ignitor/flame rod assembly  https://ebay.us/zbdTs4 - Realize we earn a small commission from qualifying purchases through our affiliate link at no additional cost to you.  Videos are provided for informational purposes only. Please naturally check with all national, state, provincial, and local codes and regulations before attempting any work. We do not assume any responsibility or liability for any damage or injury from the information provided in our videos.

As you sit there watching this video and having certain thoughts about your abilities notice that we naturally offer front load washer bearings and tub seals for when your washer starts to sound like a plane taking off when in the spin cycle. Because you can repair your water heater means you can quickly repair your washer too! Visit http://WasherBearings.com for front load washer bearing and seal kits including the Maytag Neptune front load washers!

Jeff Hartman

Sunday, October 9, 2022

Buckeyethon is Here Again


http://www.ChelsieHartman.com - It is time for the Buckeyethon fundraiser whos ultimate goal is to end childhood cancer! This annual event is promoted by The Ohio State University in Columbus, Ohio and collects gifts for Nationwide Children's Hospital... My daughter, Chelsie, graciously signed up to raise money for this important event. Any gifts would be greatly appreciated.

The 12 Hour dance marathon will be held November 4 and 5, 2022. Please share this with your family and friends... Thank you, Jeff Hartman The Neptune Man

Saturday, May 28, 2022

Are You Making These Traffic and Marketing Mistakes? (SHMI)

Are You Making These Traffic and Marketing Mistakes?

 

Ask just about any online marketer on the planet if they have enough traffic, and I bet the answer is “no.” Even the marketers who’re pulling down the huge traffic numbers want more traffic. And the reason is pretty simple: because more traffic equals more customers, more sales and more cash. This traffic information is part of my Side Hustle Marketing Ideas (SHMI) series.

 

However, while most marketers want more traffic, there’s also a good chunk of marketers who’re making some deadly traffic mistakes. That’s right, they’re shooting themselves in the foot and settling for a trickle of traffic when they could be so much more.

 

Are you making these deadly traffic and marketing mistakes too? Find out by reading on…

 

Mistake 1: Cherry-Picking Traffic Methods

 

You’ve probably read a ton of books, blog posts, articles and other materials about getting traffic. Maybe you’ve even started developing a plan for which traffic methods you’re going to use and which ones you’re going to skip.

 

Hold up there for a second…

 

If you’re completely skipping a traffic method because you think or even know that it won’t work, then that’s one thing.

 

For example, trying to generate traffic from some decade-old, untargeted source like a “start page” exchange is pretty fruitless. If you read about this in some old traffic report then yeah… feel free to ignore it.

 

What I’m talking about are ignoring proven traffic methods that are sure to bring targeted traffic to your site.

 

For example:

 

·         You don’t feel like building a list or publishing a blog, because you don’t really feel like developing and committing to a publishing schedule.

 

·         You don’t want to get joint venture partners or affiliates, because you’re happier working alone.

 

·         You thumb your nose at social media, even though your target market is young and known to hang out on Facebook all day.

 

So what if there is a traffic method that you don’t really feel like doing? Then hire someone to do it for you. Because if you want to build a thriving business, don’t skip over a promising traffic method just because you don’t feel like doing it yourself.

 

 

Mistake 2: Not Being Consistent

 

Sometimes marketers start off really enthusiastic about driving traffic to their site.  They start running ads, doing content swaps, blogging, setting up a Facebook page, optimizing their pages for the search engines, setting up an affiliate program… and so on.

 

This goes on for a few weeks, and the traffic starts coming in at a nice clip. So when the marketer sees all the targeted traffic filling up his traffic logs, he diverts his attention and starts working on something else. Many marketers think that if they stop working on their marketing, that somehow the traffic will just keep coming in on its own.

 

Of course it doesn’t work that way.

 

Content swaps lose effectiveness as the content drops off the blogger’s front page.

 

Affiliates start to lose interest and go seek out other opportunities.

 

Facebook fans and blog readers drift away when they realize there hasn’t been any new content in a while.

 

The competitors in the search engines knock your pages out of the top spots.

 

And of course paid ads don’t bring in any visitors once you stop the campaigns.

 

So here’s the point…

 

If you want to keep the traffic not only coming in but building over time, you need to do something every day to increase your traffic.

 

For example, you may do one or more of the following every day:

 

·         Recruit new affiliates or joint venture partners. You might make it a goal to find five new partners before the week is out.

 

·         Send an email to marketing partners. At a minimum, you can send them new tools to help their promotions, such as new ads, blog posts and graphics. If you really want to get them hopping, then send out an announcement about an upcoming affiliate contest.

  

·         Post something on your blog, on someone else’s blog, or on social media. Or do all three. Aim for something that will engage readers and start up a discussion.

 

·         Create a viral video. This could be something funny, super-useful or even controversial. Then post it on social media and see if you get any traction.

 

·         Send an email to your list. Then make it a point to do this regularly, as the only way to build a good relationship with them is by sending your list engaging content on at least a weekly basis.

 

·         Start up a Facebook ad campaign. Just be sure to use the ad platform’s power tool to get your ad in front of as targeted an audience as possible.

 

And so on.

 

In short: Small steps on a consistent basis lead to big results over time.

 

And now the third mistake…

 

Mistake 3: Skipping the Tracking and Testing

 

Many marketers waste a lot of time and money chasing after advertising strategies that simply don’t work for them. Maybe they’re using ineffective ads or calls to action. Maybe their lead pages suck. Or maybe they’re even posting ads in places where they’re getting very little action.

 

Why on earth would someone keep throwing money and time at advertising that doesn’t work?

 

Simple: Because these marketers have no idea their advertising doesn’t work.

 

And you know what? Unless you are tracking and testing your ad campaigns, you too might be wasting a lot of money and time running lousy ads.

 

So what you need to do is start keeping careful track of what works and what doesn’t. You’ll need a tool to track and statistically test your ads and campaigns. You can find plenty of tools around, such as Google Analytics, or the open-source alternative at Piwik.com. Check your other tools, which may have built in tracking. One good example is your email service provider, as many of the big providers can track open and click-through rates.

 

Once you decide what you’re going to test, then be sure to test just one element of your ad campaign at a time. That way, you can be confident that any change in the conversion rate is due to that one element, rather than something else.

 

For example, if you’re testing the best time of the day to send emails – 9:00am or 9:00pm -- then you need to randomly split your list into two groups and send out the exact same email to both groups. If everything else about the emails is exactly the same, then you’ll know that any difference in conversion rate is due to the time it was sent out.

 

 

Conclusion

 

These three mistakes seem pretty simple, and yet you’ll face dismal amounts of traffic if you make these mistakes too. So be sure to test everything, diversify your traffic methods, and take consistent steps every day to build your traffic.

 

Of course the question is, what all should you be doing to build traffic? And another one: what is the best way to bring in targeted traffic?

 

The answers to these questions can make or break your business, which is why you’ll want to get your answers from the best source around:  Click HERE to get instant access to this 20 video e-course training!

 

But don’t take my word for it – check it out for yourself by clicking the link above to find out what you’ve been missing. And do it now, naturally while you're thinking about it.

 

Realize that traffic is an important piece of the puzzle for your Side Hustle Marketing! Here is that link again... Click HERE to get instant access to this 20 video e-course training or click on the picture below!


Enjoy,


Jeff Hartman




 

Sunday, March 13, 2022

Side Hustle Marketing Ideas for you

Hi there, I'm putting together a list for my "Side Hustle Marketing Ideas" category. I plan to have PDF's and videos on common and unique ways for you to market your side hustle. 

This particular 40 page PDF specializes in Blogging Secrets. Realize that blogging is where I got started with this blog when I started offering Neptune STAGE 1 and Wax Motor repair kits as well as the Neptune Bearing and Seal Kits as well as other washer bearing and seal kits,,. Note that I still offer these kits!

If you have a side hustle I can recommend blogging as a great method to get leads... This PDF is a great example of how to collect leads by allowing a number of pages to be viewed, in this case 10 pages, you can set the number of viewable pages with this cool PDF viewer.


Enjoy,


Jeff Hartman



Friday, March 4, 2022

Maytag Neptune Front Load Washer Information for when replacing bearings and other troubleshooting ideas...

 Here is a document I created to help Neptuners repair their Maytag Neptune front load washers... It includes QR links to access help videos for when you're replacing your bearings and tub seal. It also has other helpful like where to purchase the replacement Neptune spacer that goes between the bearings. 

You can check out the first couple of pages...




Friday, January 7, 2022

MAH2400AWW Bearing Replacement


http://www.NeptuneBearing.com - Here is the MAH2400AWW bearing and seal kit where you can replace your washer's bearings and tub seal with some basic tools and elbow grease. Over time your MAH2400 tub seal wears and that causes water to get past the seal allowing the bearings to get really wet and eventually they will start to get louder and eventually fail. You will notice this when your washer sounds like a runaway freight train... You can replace your MAH2400 bearings and tub seal and save a lot of cash. Click on link above for more information! Let me know if you enjoy fixing things! Jeff Hartman The Neptune Man


Tuesday, December 21, 2021

Another Special Neptune Help Song Video I Created For You


Here is another cool video type I can quickly create for you that has video in video technology to help set you apart from among the others... I sneakily placed my Neptune Help Song video inside a tablet of all things.. Thank you, Jeff Hartman http://www.JHartmanDigital.com