Maytag Neptune Front Load question - Water still in tub

Maytag Neptune Front load - Here is a question I get a lot: 

Q: I have a Maytag Neptune that doesn't drain. It spins the water out of the clothes but the bottom of the machine has enough water in it that you can hear it when you turn the drum. 

 A: Perhaps it is draining after all... The water you hear when you turn the inner tub is the balance ring which has liquid in it and it is part of the balancing system on the Neptunes. Now, if there is physically water visible in the inner tub then the pump is not getting all of the water out and it needs to be investigated. There are a number of issues that can cause this. One is a clogged tub drain or tub drain hose that feeds the pump. It could also be that the pump has debris in it or the drain hose in the back of machine is kinked... Whatever the reason it needs to be corrected or naturally your Neptune tub bearings will not last long.

The reason is because the tub seal is not designed to work against the water slinging in the tub during spin cycle. Once water get passed the seal it will get into the bearings and cause the lubrication to break down. The next thing you will notice is that the your Neptune will get louder in spin cycle where it sounds like a jet plane taking off. At this point you will want to replace the bearings and seal. 

You can do it yourself and save lots of money. See http://www.neptunebearing.com/ for more information regarding the Neptune Bearing Tool Kit rental as well, which was designed to save you time and effort when replacing your Neptune bearings. It even includes video access that you can watch that shows how to disassemble your Neptune, replace bearings and install the seal kit. Until next time...

Jeff Hartman

Maytag Neptune Washer - Bearing Spacer Question

Maytag Neptune Washer - Bearing Spacer Question:

I've been asked a few times lately regarding the installation of the new bearing spacer so I wanted to post the answer here. If you will look at the picture you will notice one end of the spacer is flat and the other end has a slight bevel.

The beveled end goes towards the rear of washer because you don't want the spacer rubbing the seal on the rear bearing.

If you have a Maytag Neptune front load washer check out Maytag Neptune Bearing for replacement bearings and the seal kit. When you notice your Neptune getting loud in the high speed spin cycle is when it is time to change your bearings. You don't want to wait too long to change them because the bearings will eventually fall apart and that will make it more difficult to get them out of there.

One last thing... If your Neptune front loader has the timer dial, you need to see if you have the faulty door latch wax motor. See Maytag Neptune wax motor for a video that explains the issue.

Until next time...

Maytag Neptune Help songs revealed

Hi Neptuners,

I almost forgot to reveal to you who created the Neptune Help Song and the Neptune Bearing song...

I previously mentioned that his name was Mark.

Here is the scoop:

Mark Hockenberry is who created those fantastic jingles for me. You can check out his website at Background Acoustic where he has some free mp3's he created for you to download. If you have a website and would like some custom background music then I highly recommend that you talk to Mark. You could also use Background Acoustic music for a custom picture show video you are putting together for a family reunion, your childs school class photos, etc.

Again, the songs are at the following sites:

Neptune Help Song

Neptune Bearing song


Check them out!


Until next time...

Cracked Glass Cooktop Website Updated

Hi Neptuners,

Some of you may be aware that I offer replacement glass cook tops for most ranges and cook tops.

In the past, I required folks to email me via a form that asks for name, phone, model, serial, etc. and I would take the information and look up the glass cook top to see if I could provide a replacement. I would then send an email with the price quote, etc.

I just re worked the www.crackedglasscooktop.com site and added a model number entry box at the bottom of the page where you can enter your model number directly and it will take you to another page where all of the parts to your range will be displayed with prices. This way the process is instant plus it takes me out of the loop.

Another important fact is you can look up any appliance parts such as your fridge, range, dish washer, etc. What convenience?

Keep me in mind if you need appliance troubleshooting help...

Until next time...

Maytag Neptune Washer - Bearing Spacer

Maytag Neptune Washer - Bearing Spacer

I just added the replacement Neptune bearing spacer to the http://www.neptunebearing.com/page4.html order form near the bottom.

Occasionally, the bearing spacer needs replaced when swapping your Neptune tub bearings out.

Over the years, I've seen cracked spacers and badly corroded bearing spacers.


Note: These replacement Maytag Neptune Spacers are much thicker than the original Neptune bearing spacers.



The two photos show the Neptune bearing spacer next to a quarter for size reference.

Maytag Neptune Bearing - I Shipped A Tony Tool to Canada

Maytag Neptune Bearing Update - I just shipped my first Tony Tool rental kit to Canada via UPS Ground. The location I shipped it to was Glen Huron, Ontario Canada.

It is no surprise because there is a large number of Maytag Neptune owners in Canada that I have sold the Q6 & R11 repair kits to. I have received a number of tool rental requests but I declined to ship the tools to Canada for a number of reasons...

1. The UPS Ground shipping time will be greater than the Flat Rate Priority Mail I use for the domestic orders which ties up the tool for longer. It weighed 15 pounds which tells me David is getting the solid steel knock out plug...

2. Customs - Getting the tools through customs was concerning because these were rental and we should not have to pay duty on them when you declare the value of $425.00.

3. I also included a bearing spacer just in case David's spacer is damaged or corroded.

4. DVD - I don't know if the Tony Tool DVD will play in Canadian players because DVDs have a country code.

5. Shipping expense - The UPS Ground shipping expense was about $35.00 USD Verses $15.55 for Flat Rate Priority Mail shipping in the States. I will have to hold back more of the refund to cover the additional shipping expense to Canada or get a higher deposit up front.


To rap it up... Before we get excited about renting the Neptune Bearing Tony Tool to Neptune owners in Canada let's see what happens with David's Neptune and see if I get the tool back from Customs, etc.

In the meantime, if you are in the States you can order your Tony Tool rental at www.neptunebearing.com.



Until next time...

Maytag Neptune Bearing Tony Tool Update

Maytag neptune bearing information - The Maytag Neptune Bearing Tony Tool has been improved! Could this be a dumb bell?

I believe it could be! But more importantly... The original PVC knockout plug has been upgraded to solid steel! The biggest issue with the Tony Tool has been the PVC Knockout plug because it would crack near the top lip and folks who rented the tool kit at www.neptunebearing.com would call or email me apologizing and offering to buy a new one. I would just explain to them that it was not an issue and don't worry about it.

I just figured that you Neptune owners were taking your frustrations out on the knock out plug like a stress relieving squeeze toy. But no, Tony mentioned that his personal PVC knock out plug was cracked too and that it still worked great for getting the front bearing out. 

There is a danger when using the steel knockout and that is if it falls down it can damage components on the floor of your Neptune washer because it is so heavy... so I decided to keep the much lighter PVC knockout plugs with the tool kits.

Until next time...