MAH6500AWW Bearing and Tub Seal – How To Replace

MAH6500AWW Bearing and Tub Seal – How To Replace

If you own a MAH6500 and it sounds like a freight train it is time to replace your bearings. If you bother Ole’ Lonely he will quote you at least $950 or suggest that you scrap machine. You don’t want to scrap machine because you can save money by replacing your Neptune tub bearings and seal and be washing clothes soon. Ole’ Lonely will want to replace your large outer tub which runs over $500 alone! You don’t need to replace the expensive outer tub.

There are two seals that are available in the genuine 12002022 seal kit. The earlier lip seal and the revised lip seal. If you have the earlier lip seal (with plastic white spacer clip) you will need to replace it with the new earlier lip seal in the kit. If you would like to install the revised lip seal you will have to replace your W10181639 spinner support because its shaft is machined different.

It should take about 1 – 4 hours depending on how much cleaning you need to do while you’re in there and no special tools are required. You could save time by renting the Tony Tool which pulls the rear bearing out first. You then knock the front bearing out and then after some clean up you use the Tony Tool to install the new bearings and spacer. The tool kit rental includes an extra bearing spacer just in case you need it. The Maytag Neptune Bearing and 12002022 Seal kit also includes an ebook with more information and tips to help you be successful.

Depending on how long your machine has sounded like a jet plane you may need to heat up the aluminum hub when extracting the inner or front bearing. The aluminum has a higher expansion coefficient than the steel bearing does so the bearing housing should expand more than the bearing does thus loosening it up. Just don’t over heat it since some of the heat guns can really get hot.

The good news is that you don’t have the faulty brown tipped wax motor in your door latch. Only the timer knob based Neptune’s have the wax motor which would fail and damage the Q6 triac and R11 and the upper control board. See Neptune Help for more wax motor information. The digital Neptune models all use a solenoid to lock the door.

I hope this was helpful to you. 

Please leave any comments below.

Jeff Hartman

  

               

Neptune Bearing Replacement - How To

Neptune Bearing Replacement - How To

 If you have a Maytag Neptune Front load washer there will come a time when it starts to morph into a jet plane or even a freight train..


Since you probably don't want a jet plane in your home you will want to replace your Neptune tub bearings and seal asap.

You can replace your washer bearings without the special Neptune bearing replacement tool or Tony Tool if you're handy with tools. The tool kit does save you time and effort when changing your bearings. The tool kit rental includes the tub bearings, 12002022 seal kit, bearing spacer, 2" wire wheel and step by step DVD. You can order the Maytag Neptune bearing and 12002022 Seal Kit HERE and it works on all solid door (no window) panel Neptune's. 

You can find other washer bearing and seal kits HERE.

I hope this post was helpful.

Thank you,

Jeff Hartman

P.S. For other appliance parts you can visit www.washerbearings.com/parts get new replacement parts for your appliances.

Otherwise you can always use the Neptune Washer Back up Plan which is shown below...

You can now spread your Neptune bearing replacement over 6 months, if needed

For my bearing and seal business I use PayPal, which accepts major credit cards, and they are offering an option when checking out for orders over $99, U.S. customers only, where you can get 6 monthly payments same as cash. So… if you've been putting off that bearing replacement now is the time for you to add more years to your Neptune’s life and spread the bill over 6 months with no interest.

See Neptune Bearing replacement and click on the PayPal banner on the left side for offer details.

If you decide to just purchase the Maytag Neptune Bearing and 12002022 Seal kit (not rent the tool kit) then you could add the door boot or belt so you exceed the $99 order amount to qualify. If you have an MAH3000, MAH4000 model you may want to order the bearing spacer just to have on hand in case yours is cracked or really corroded. If you decide to order a belt and don’t need it after inspecting your belt then simply send it back unopened for a refund. Don’t forget that a new bearing spacer is included with the Tony Tool kit rental so you don’t need to order one.

If you decide use the 6 months option just make sure you make payments to avoid any interest charges.

Other options if your Neptune washer needs bearings:

Use a local laundromat until you can save enough for bearing replacement
Buy a used unit on Craigslist
Visit relatives, neighbors and wash your clothes
Use washing board. See Neptune backup plan

Leave me a comment if you have another suggestion on where to launder your clothes until your machine can get fixed.

TIP: When sorting clothes check the pants pockets for loose change that can get into the pump and cause draining problems. 

I also offer other washer bearing and seal kits...  See Washer Bearings for more information.


Until next time...

Neptune Bearing Spacer. Note: beveled end goes towards smaller rear bearing

Neptune Washer Bearing – Special tool saves time and effort

Neptune Washer Bearing – Special tool saves time and effort




Maytag Neptune bearing noise

It is obvious that your Neptune’s bearings are failing because your Maytag Neptune sounds like jet taking off when entering the spin cycle. Where do you start? Should you get a quote to have the Neptune repaired? Can you complete the repair yourself and save money? Should you purchase a new washer and dryer? How long will the washer be down? Etc…


Maytag Neptune washer bearing replacement

Let’s start with what a technician will quote you and why you will experience sticker shock. The quote to repair the bearings will run from $800 to $1,000 and the reason is that 99.4% of the repair techs will replace the large outer tub which runs about $500 alone plus labor and maybe a new spinner support in case yours is damaged. The truth is that you cannot tell if the spinner support shaft is damaged until you get in there but from my experience in most cases the spinner support is reusable. You can just replace the bearings and seal and get many more years of life from your Neptune front loader. There are a number of technicians using the Tony Tool to save Neptuner’s money so they won’t suggest that you replace the $500 outer tub.

I do recommend if you’re reading this and your bearings are still functioning that you proactively replace your Neptune bearings if your machine is 10 years old or more.


Maytag Neptune bearing kit

If you’re handy with tools you can replace your Neptune bearings without the special tool kit rental. There are a few things you need to know about how the bearings are installed in the machine. The front bearing is slightly larger than the rear bearing and there is a 1 ¾” pipe (bearing spacer) that is sandwiched between the bearings. When you remove the front tub seal you will see the front bearing and when you look at the front bearing’s ID you will see a tunnel because of the bearing spacer. Then you will see the rear bearing’s inner race where you have about 1/8” lip to grab onto to push or pull it out. The tool kit has a machined round nut that glides through the front bearing and spacer and will catch the rear bearing’s inner race and uses the leverage from the t handle to draw it out. Once the rear bearing comes out the spacer falls out, too.

Upon installation you install the rear bearing first using the tool. Next you place the bearing spacer on the PVC spacer holder and then start to draw the front bearing in. The tool kit makes this a breeze since it keeps the spacer centered while the front bearing is being drawn in and finally clamps the bearing spacer. If you don’t have the tool kit you have to come up with a way to hold the spacer when you install the bearings. So the tool kit rental saves you time and effort.


How to replace your Neptune bearings

The Neptune bearing tool kit rental includes bearings, 12002022 seal kit, a pair of snap ring pliers, 2” wire wheel, emery cloth, step by step DVD and an extra bearing spacer in case yours is cracked or corroded. Note: The earlier Neptune’s have a snap ring that you need to remove before pulling it. The wire wheel is to clean out the bearing housing after bearings are removed and the emery cloth is to smooth the front bearing seat in case of any ridges or ripples that may have developed due to the failed front bearing. The kit is shipped Priority Mail to you so you will receive it within 2 – 3 days typically. The http://www.neptunebearing.com/ site displays the estimated to ship days based on when tool kits return.


The Neptune 12002022 Seal kit

The 12002022 seal kit includes 2 seals. The earlier lip seal and the revised lip seal. You need to use the same one that you removed since they require different shaft machining. I have had some Neptuner’s decide to replace the spinner support so they could install the revised lip seal when their machine originally had the earlier lip seal but it is not necessary.


Maytag Neptune Washer MAH5500BWW bearings

I personally replaced the bearings and seal on a MAH5500BWW washer in 1.5 hours and it was my 2nd time of using the tool kit. I would also recommend having an 8 – 10 pound sledge hammer available when changing the bearings.

If you decide to use the to neptune bearing tool or go it alone you can get everything you will need at Neptune Bearing.

Until next time...

Maytag Neptune Front Loader tub bearing replacement tip

Maytag Neptune Front Loader tub bearing replacement tip

If your Maytag Neptune front loader is at least 10 years old I am highly recommending that you replace your tub bearings and seal proactively and let me explain why.


Eliminate the #1 Tony Tool challenge which is getting the rusted front bearing out…
As you know… I rent the specially designed Tony Tool to Neptune owners to assist them when changing their bearings and seal and I will tell you the number one challenge when changing the bearings is getting the front bearing out. In the past, Neptuner’s only replaced their bearings after the machine sounds like a jet taking off because the seal has leaked water into the bearings. What happens next is that rust forms between the front bearing outer race and the aluminum bearing housing making the front bearing difficult to extract. If you replace the bearings before they rust… the front bearing will come much easier with less stress to the machine. The tool kit rental comes with a pair of snap ring pliers, 2" wire wheel, extra bearing spacer and emery cloth as well as the bearings and 12002022 seal kit. A DVD is included that shows you how to disassemble your Neptune, swap bearings and install the seal kit. You can order the tool kit rental at Neptune Bearing.  Go down about half way and click where is says " Click HERE to read the tool rental agreement & order. Once the tool rental agreement opens up then there will be an Add to Cart button on the left side. Click on the Add to Cart button and you will be taken into PayPal's secure server to complete the payment.

Prevent spinner support (shaft) damage…
In some Neptune bearing failure cases the spinner support shaft was damaged because a bearing hung up and that caused a groove in the shaft so it had to be replaced at $89.00. The upfront cost for a new spinner support is $129 delivered via UPS Ground but I allow you to send the 12002022 seal kit back with the tool kit rental for an additional $40 refund because the spinner support arrives with a revised lip seal so you won’t need the 12002022 seal kit I sent you with the tool kit. The $40 seal kit refund takes the $129 down to $89. See Spinner Support to order a new spinner support.

The tool rental queue is lower than usual so you will get it quicker…
I will admit that the Neptune bearing tool kit rental queue is low right now which means that you will get a tool kit quicker than usual and that is a good thing. In the past I would have anywhere from 8 to 15 people in the queue with all of the tool kits out in the field. However, it is less critical in your case because your machine is not down and you are being proactive.

You can control washer downtime by replacing your bearings proactively…
Another benefit being proactive is that you control the washer downtime. You can do all of the laundry before you start the disassembly so there is less pressure to complete the bearing swap out. If your bearings fail and there are a large number of Neptuner’s in the queue that will delay you receiving the tool kit and then that would mean visits to the Laundromat or relative’s houses to do your laundry.

Take the time to really clean your Neptune while you have it apart…
Does your Neptune smell funky? I get lots of feedback from Neptuner’s and they tell me that they took extra time to really clean out their Neptune while they had it apart to freshen it up. There are simply areas that you cannot get to and properly clean until you disassemble the machine. From there, you can start a regimen of using the Affresh tablets or other front load cleaning product to help prevent the buildup of smelly gunk and keep your machine smelling better. You may also consider replacing the door boot while you change your bearings and seal. You can order one for $49.00 when your rent the tool kit.

Other parts you may want to replace while your Neptune is disassembled…
To wrap it up... Don’t forget that you can also get the new Neptune belt for $26.00 and the new door boot for $49.00 from the Neptune Bearing order form. If you take machine apart and decide your belt still looks good then just send it back with the tool kit unopened for a $26 refund. If you have a timer knob then you will want to make sure that you replace your door latch wax motor before it fails. Order extra wax motors for only $12 when you rent the tool kit!

Top 5 reasons to proactively change your Neptune front loader bearings.
1. #1 tool kit rental challenge is eliminated as the front bearing will come right out

2. Prevent potential damage to the spinner support

3. The Neptune bearing rental queue is very low right now

4. Totally prevent unexpected downtime and Laundromat visits

5. Funky Smelling Neptune’s can be really cleaned out when they are disassembled

Again, here is that link to order the Neptune bearing tool kit rental...  Neptune Bearing.


Until next time...

Maytag Neptune Bearing - www.neptunebearing.com is now a member of the BBB

Hi Neptuner!

I wanted to let you know that I received the important BBB accreditation for my Neptune Bearing site where I offer replacement bearings and seal kits for the Maytag Neptune front load washers.

I also rent the Neptune bearing tool kit as well which includes the Neptune bearings, Maytag 12002022 seal kit, bearing spacer, wire wheel, snap ring pliers, tool kit usage, tech support and a step-by-step instructional DVD.

Neptune Help is also included with the accreditation and I will add my following other Neptune related sites as well.

By adding the BBB accreditation to my Neptune sites it means that I support the BBB's services to the public and meet their tough accreditation standards and that you can trust me to provide excellent service!

Until next time...

Maytag Neptune Washer - Bearing Spacer Question

Maytag Neptune Washer - Bearing Spacer Question:

I've been asked a few times lately regarding the installation of the new bearing spacer so I wanted to post the answer here. If you will look at the picture you will notice one end of the spacer is flat and the other end has a slight bevel.

The beveled end goes towards the rear of washer because you don't want the spacer rubbing the seal on the rear bearing.

If you have a Maytag Neptune front load washer check out Maytag Neptune Bearing for replacement bearings and the seal kit. When you notice your Neptune getting loud in the high speed spin cycle is when it is time to change your bearings. You don't want to wait too long to change them because the bearings will eventually fall apart and that will make it more difficult to get them out of there.

One last thing... If your Neptune front loader has the timer dial, you need to see if you have the faulty door latch wax motor. See Maytag Neptune wax motor for a video that explains the issue.

Until next time...