Maytag Neptune Bearing Tool Kit Rental Special For July, 2019

Goto www.neptunebearing.com for more information.


Jeff Hartman
"The Neptune Man"



For the latest federal tax refund information go to www.neptunebearing.com/tax.html

Neptune Bearing Tool Kit Rental - Use Check or Money Order for Deposit

After numerous requests for clients that prefer not to use PayPal or credit cards... here you go!

Visit www.neptunebearing.com to find out more information about replacing your Maytag Neptune bearings and seal.




Thank you,


Jeff Hartman
"The Neptune Man"

Please leave a comment if this new option helps you...

Maytag Neptune Bearing Replacement - Cleaning Tips

As you're replacing your Maytag Neptune bearings and tub seal it would be a good time to perform some housekeeping while in there.

If your washer is over 8 years old you will probably have some soap and debris build up on the backside of the inner stainless steel basket and on the inside of the large outer tub. Some clients have used a power washer to carefully clean their Neptune washers. If you decide to use a power washer make sure you protect any electronic circuit boards and keep them dry. You have the motor control board down by the floor on the right side and the machine control board is located in the top console section.

Another option is to remove the outer tub from cabinet and take out back and spray it so you don't risk getting something wet that should not be wet.

The tub cover has a arched brush on the bottom have to help keep things from getting between the inner basket and outer tub. The brush will probably be gunky. You cannot replace just the brush as it is part of the tub cover.

For more information on replacing your Maytag Neptune bearings and seal see my www.neptunebearing.com page.

Feel free to leave feedback below and let me know how you decided to clean your Neptune washer while you had it apart during your bearing and tub seal change.

 

Jeff Hartman

"The Neptune Man"

Neptune Bearing Replacement - How To

Neptune Bearing Replacement - How To

 If you have a Maytag Neptune Front load washer there will come a time when it starts to morph into a jet plane or even a freight train..


Since you probably don't want a jet plane in your home you will want to replace your Neptune tub bearings and seal asap.

You can replace your washer bearings without the special Neptune bearing replacement tool or Tony Tool if you're handy with tools. The tool kit does save you time and effort when changing your bearings. The tool kit rental includes the tub bearings, 12002022 seal kit, bearing spacer, 2" wire wheel and step by step DVD. You can order the Maytag Neptune bearing and 12002022 Seal Kit HERE and it works on all solid door (no window) panel Neptune's. 

You can find other washer bearing and seal kits HERE.

I hope this post was helpful.

Thank you,

Jeff Hartman

P.S. For other appliance parts you can visit www.washerbearings.com/parts get new replacement parts for your appliances.

Otherwise you can always use the Neptune Washer Back up Plan which is shown below...

Maytag Neptune Washer Seal Replacement - How to replace

Maytag Neptune washer seal replacement - If you notice your Maytag Neptune front load washer starting to sound like a freight train you should know that it is time... Time to replace your Maytag Neptune bearing and seal. Although, you can rent the special Neptune bearing tool kit you can replace the bearings without it. The photo above shows the Neptune bearing and a revised lip seal, o ring and installation cup. If you have the earlier lip seal you cannot install the revised lip seal because the spinner support shaft is machined different than the spinner support shaft that uses the revised lip seal. If you replace the Neptune spinner support it will come with the revised lip seal. I would recommend having a large 8 pound hammer available just in case when replacing your Neptune tub bearings... Let me know if you have any questions. Jeff Hartman

Hey Neptune Man song

OK, I have another treat for you today... Listen to my new "Hey Neptune Man" song and see if you can recognize which song it sounds like... Enjoy.




I hope you enjoyed that song!

See Neptune Washer for more information on the wax motor and bearing replacement kits.

Until next time...

Cat gets caught barking by a human and resumes meowing

Cat gets caught barking by a human and resumes meowing


Ok.. You've gotta be "kitten" me! I have to admit I’ve never seen or heard a cat bark before until this video clip but I have heard a Maytag Neptune front loader bark when its bearings are going south.

See Neptune Bearing before you have a "cat"astrophe and the laundry is piling up! You can even rent a special tool kit to help keep your fur from getting roughed up.

By replacing your Neptune bearings and seal you will have your Neptune purring like a kitten again!

Here is the video...



Until next time...

Maytag Neptune Bearing Tool rental Update

Maytag Neptune Bearing Tool rental Update 

 Hi Neptuner,

Whirlpool Duet Sport seals are in… I have a batch of Whirlpool Duet Sport seals in and they can be purchased at http://www.duetbearing.com/ along with the bearings, too. The Original Duet Sport seals have FSP, ATP-1-17 and 8540091 on them. The Duet Sport bearing and seal kits are closer to the bottom of the order form. 

For you history buffs… You can now see Roman London as it was 2,000 years ago… Streetmuseum Londinium will be free to download for iPhones and iPads worldwide. Users can look through their phones and see the past emerge, locked as an overlay across the present scene. These can be viewed as ghostly alignments, or the archive images can be brought up and explored in detail, along with information about the Museum’s photographs and paintings. So far 200,000 people have downloaded Streetmuseum worldwide, from Argentina to New Zealand. Visit https://www.museumoflondon.org.uk/discover/museum-london-apps for more information. 

 Until next time...

Maytag Neptune Bearing - www.neptunebearing.com is now a member of the BBB

Hi Neptuner!

I wanted to let you know that I received the important BBB accreditation for my Neptune Bearing site where I offer replacement bearings and seal kits for the Maytag Neptune front load washers.

I also rent the Neptune bearing tool kit as well which includes the Neptune bearings, Maytag 12002022 seal kit, bearing spacer, wire wheel, snap ring pliers, tool kit usage, tech support and a step-by-step instructional DVD.

Neptune Help is also included with the accreditation and I will add my following other Neptune related sites as well.

By adding the BBB accreditation to my Neptune sites it means that I support the BBB's services to the public and meet their tough accreditation standards and that you can trust me to provide excellent service!

Until next time...

Maytag Neptune Question about the W10181639 Spinner Support

Hi Neptuner!

Here is a Maytag Neptune Spinner Support question that I received lately...

"I have a spinner support with a broken bolt stud. Can you replace the bolt studs in the spinner support, or do you have to replace the entire spinner support? If I have to replace the spinner support, do you have them and what does it cost? I will also replace the bearing and seal when I fix the spinner support."

A: I've had Neptuners successfully replace a broken stud on the spinner supports. You will want stainless steel replacement hardware. Sometimes the end of the spinner support arm corroded away and the spinner support needed replaced. You can order a new Neptune spinner support at w10181639.com. Note: I have a photo of a brand spankin' new spinner support above...

In addition, the new spinner support comes with the revised lip seal, too. So if you're replacing your bearings you can get a $40 refund if you purchased bearings from Neptune Bearing or even rented the Neptune bearing tool kit which almost pays for half of the new spinner support! Please don't open the 12002022 seal kit... just send it back for your $40 refund...

Don't forget to replace your 12002535 door latch wax motor if you have an earlier timer version (non digital) Neptune front loader with the original one still in it before it chokes and smokes your machine control board. See Neptune Help for more information.

Until next time...

Water Ice Maker information

Recently, I've had some requests for information on replacement ice makers because I offer the Maytag Neptune front load washer help to homeowners. I do have access to most makes of major appliance replacement parts.

I just created a new website that offers the most popular replacement ice makers at Water Ice Maker. If your ice maker is not doing its job efficiently maybe it is time to replace it. Check it out NOW!

If you own a Maytag Neptune front load washer you need to know a few things about these machines that can save you money! If your machine has a timer knob (non digital) then you need to know about the door latch wax motor issue where the wax motor shorts out and damages the machine control board.

You can prevent the Q6 triac and R11 resistor burnout by proactively replacing your wax motor before it fails with the new redesigned wax motor. There is a video that shows how to inspect your door latch to see if you have the faulty wax motor and there is a video that shows how to swap it too! The website is Neptune help.

Next, I developed a low cost bearing and seal kit so you can replace your bearings when the machine starts to sound like a jet plane taking off when it ramps up for the spin cycle. See Neptune Bearing for more information. There is even a Neptune bearing tool kit rental available to help you change your bearings and it includes use of a DVD that shows the disassembly, bearing swap and the seal kit installation.

Both of these Neptune kits were created to save you a ton of money in service calls and even machine replacement by getting more years out of your Maytag Neptune front loader!

Until next time...

2009 Chevrolet Malibu and 1959 Chevrolet Bel Air crash

Maytag Neptune repair - Off topic post for you...

Wow, which vehicle would you rather be in during a 40 mph crash... A large, heavy 1959 Chevrolet Bel Air or a 2009 Chevrolet Malibu during a crash? I know which one I would pick... Only after seeing the video!

Go ahead and check it out at 2009 Chevrolet Malibu and 1959 Chevrolet Bel Air and leave a comment on your thoughts after watching the video clip.

When your Maytag Neptune front loader crashes check out Neptune Help for repair information, genuine Maytag replacement parts. In addition, if you have the Neptune front load washer with a timer knob (non digital) you will want to replace your 12002535 door latch wax motor if you have the original one in there.

Lastly, did you know that you can replace your Neptune bearings and seal when your machine sounds like a jet plane taking off? See Neptune Bearing for more information on replacing your bearings and saving a ton of money...

Maytag Neptune Bearing Seal Kit Question - 12002022

Maytag Neptune - Earlier Lip seal tips

Hi Neptuners!

Ok... Let's get something straight... Yes, the Maytag Neptune 12002022 seal kit installation instructions are not very clear. So I will give you some tips on installing the 'earlier' lip seal...

In the 12002022 seal kit there are two seals. The thinner one is the earlier lip design and it has the steel washer embedded into it. On the spinner support, near the three arms, remove the steel washer which is remains from the original seal. If you don't remove it, you will have 2 steel washers on the shaft and when you tighten the new included pulley bolt to 33 ft lbs, the tub will be hard to turn and you will have to pull the inner tub again. If you proceed to run the machine with the 2 steel washers on the spinner support shaft you will damage the new seal.

Since some steel washers will be tight on the shaft due to tolerances, it is a good process to tap the new seal in so it is flush and level to the bearing housing. Tip: I use the old front bearing so I don't deform the steel washer when tapping in. Then pull the steel washer out (split the seal) and place it on the spinner shaft (without flipping it) and work it all the way back to the three arms just like the original one was. Be careful not to disturb the pink grease when working the steel washer back. The split seals will meet up again when you install the inner tub. Make sure that after you torque the new included 9/16" pulley bolt that you can turn the tub by hand fairly easily and hear the liquid sloshing around in the balance ring.

The 'O' ring works only with the revised lip seal. The new replacement spinner supports will come with a special seal kit with the 'revised' seal and "O" ring.

Don't forget that you can rent the Neptune Bearing Tool Kit from Neptune Bearing which includes a 14 minute DVD that shows you the disassembly process, bearing swap and the seal kit installation to save you lots of time on the Neptune bearing job.


I hope this helps get your Neptune back up and spinning again...


Until next time...

P.S. Don't forget that if you have a Neptune front loader with a timer knob to replace your faulty door latch wax motor before it damages your machine control board. See Neptune Help for details...

Maytag Neptune Front Load question - Water still in tub

Maytag Neptune Front load - Here is a question I get a lot: 

Q: I have a Maytag Neptune that doesn't drain. It spins the water out of the clothes but the bottom of the machine has enough water in it that you can hear it when you turn the drum. 

 A: Perhaps it is draining after all... The water you hear when you turn the inner tub is the balance ring which has liquid in it and it is part of the balancing system on the Neptunes. Now, if there is physically water visible in the inner tub then the pump is not getting all of the water out and it needs to be investigated. There are a number of issues that can cause this. One is a clogged tub drain or tub drain hose that feeds the pump. It could also be that the pump has debris in it or the drain hose in the back of machine is kinked... Whatever the reason it needs to be corrected or naturally your Neptune tub bearings will not last long.

The reason is because the tub seal is not designed to work against the water slinging in the tub during spin cycle. Once water get passed the seal it will get into the bearings and cause the lubrication to break down. The next thing you will notice is that the your Neptune will get louder in spin cycle where it sounds like a jet plane taking off. At this point you will want to replace the bearings and seal. 

You can do it yourself and save lots of money. See http://www.neptunebearing.com/ for more information regarding the Neptune Bearing Tool Kit rental as well, which was designed to save you time and effort when replacing your Neptune bearings. It even includes video access that you can watch that shows how to disassemble your Neptune, replace bearings and install the seal kit. Until next time...

Jeff Hartman

I have a Maytag front load Neptune MAH5500BWW problem

Q: Hi. I have the MAH5500B washing machine. My wife called in a panic and said the LCD panel displayed the LR code. I read 120V ac at the receptacle. I read 120V ac at terminals 1 and 3 on connector P6 at the machine control panel. I ran the Quick Service Cycle and everything seems to function except the tub does not spin. Checking across the 10 amp fuse on the motor control board yields 1 ohm resistance. I am thinking motor but I am not sure...any ideas? 

 A: Sure. You will have to replace the Motor control board and the motor with the new Maytag 12002039 motor conversion kit which may be available on ebay https://ebay.us/Aac7zW. If you already have the newer motor control board with plastic cover, you can try just replacing your motor control board. You can look at the photos on ebay and see if they look like your motor control board.

 

It takes about an hour to install. The original motor control boards have a high failure rate on the Neptunes so Maytag decided to redesign both the motor and motor control board. 

 Have you noticed your Neptune getting loud in spin cycle? If so, then your bearings are failing and will need to be replaced. The extra friction caused by the failing bearings can cause the motor control board to shutdown and/or fail. You can get new bearings and seal kit from www.neptunebearing.com. They also rent the special Neptune bearing tool to save you lots of time and effort and the rental incudes access to a video that shows you how to teardown machine, replace bearings using tool and install the seal kit. If you ask a service technician to come over you will receive a dose of sticker shock! They will quote you over $900 to quiet your machine again...

Until next time...

Will your Maytag Neptune bearing and seal kit fit my MAH55FLBWW Neptune?

Here is a question I received recently...

Q: "Hey there... I have a Maytag Neptune front loader washing machine, with the typical bearing failure. Im interested in buying your repair kit, however I need to know for certain it will fit my model. My model is MAH55FLBWW. Thanks for your time."

A: Hello, yes the bearing and seal kit will fit your Neptune. See www.neptunebearing.com for information on the Neptune bearing and 12002022 seal kit. I also offer the tonytool for rent so you can save time while replacing your bearings.

New Maytag Neptune tonytool comment

Here is a comment from Dan K. today regarding the tonytool he rented from www.neptunebearing.com. 

"Jeff thanks much, by the way the DVD video is great. It is funny and it was easy to follow. Thanks again for a well designed tool. Dan K." 

Well, Dan, I can't take credit for the Tony Tool design... So far I have received great feedback from folks that have rented the Tony Tool to assist in changing their Neptune bearings. You will know when it is time to replace your bearings when your Neptune front load starts getting loud in high speed spin cycle. 

By the way... If you bother the lonely Maytag repairman it will set you back around $1,000 to have it repaired the expensive way which is to have the whole outer tub replaced! Ouch! 

Why change the outer tub? When you can change just the bearings and seal kit?

Until next time...

Tony Tool substitute?

One of my customers who rented the Tony Tool offered a suggestion for the PVC knock out plug. He smashed his fingers using the PVC knock out plug because it is too short for his liking. It turns out he made a new front bearing knockout tool using 1 1/2 pipe and fitting. He even sent the contraption back with the tony tool kit so I took a photo of it compared to the Tony Tool knock out plug. 

It looks like it has about 2 more inches to work with. Who says bigger isn't better? I was surprised because this is the first complaint I've received for this tool kit. Everyone else praised the tool kit and how much time it saved them. 

If your Maytag Neptune is starting to squeal while in high speed spin I would recommend replacing your bearings as soon as you can. You want to catch them before they separate which makes the bearings much more difficult to get out because the Tony Tool relies on the inner bearing race to pull it out. 

To purchase the Neptune bearings, seal kit and Tony Tool rental point your browser to http://www.neptunebearing.com/. 

If you have not replaced your door latch wax motor yet you need to check out http://www.neptunewaxmotor.com/ to see if your Neptune is affected by this defective part that will run $450.00 to repair if you bother the lonely ole' Neptune repair guy!

Until next time...

steve jobs heart attack?

I heard this was not true... Where do these reports come from? Anyway.... If you own (or know of anyone who owns) a Maytag Neptune front load washer please check out www.neptunewaxmotor.com for important reliability information that could cost you $450.00 to repair. It involves the defective 12002535 door latch wax motor that can be replaced and prevent the machine control board failure. 

See www.neptunebearing.com for information that could save you $900 when your Neptune bearing starts to fail. There is even a effort and time saving tool kit you can rent to reduce the bearing replacement time considerably. When your machine sounds like a jet taking off in spin cycle then it is time to replace the bearings and 12002022 seal kit.

Until next time...

Is the Tony Tool rental available in Canada?

Since I started renting the revolutionary Maytag Neptune bearing replacement tool, the Tony Tool, I have received a number of requests to ship the Tony Tool kit to Canada. 

Presently, I only offer the tool kit rental to the United States since the tool kit would have to pass customs and a duty would have to be paid for the $425 value both ways? 

Does Canada have an duty exemption process for tools crossing the border that will be returned? The other issue is the transit time. It would take at least a week to get there which ties up the tool too long compared to the 2 - 3 days required with the Priority Mail here in the states. 

It might be more time / cost effective for someone in Canada to offer the Tony Tool for rent? If you would like more information on the Tony Tool, see www.neptunebearing.com.

Until next time...