Showing posts with label MAH6500. Show all posts
Showing posts with label MAH6500. Show all posts

Sunday, April 20, 2014

Neptune Bearing Replacement - How To

Neptune Bearing Replacement - How To

 If you have a Maytag Neptune Front load washer there will come a time when it starts to morph into a jet plane or even a freight train..


Since you probably don't want a jet plane in your home you will want to replace your Neptune tub bearings and seal asap.



You can replace your washer bearings without the special Neptune bearing replacement tool or Tony Tool if you're handy with tools. The tool kit does save you time and effort when changing your bearings. The tool kit rental includes the tub bearings, 12002022 seal kit, bearing spacer, 2" wire wheel and step by step DVD. You can order the Maytag Neptune bearing and 12002022 Seal Kit HERE and it works on all solid door (no window) panel Neptune's. 

You can find other washer bearing and seal kits HERE.

I hope this post was helpful.

Thank you,

Jeff Hartman


P.S. For other appliance parts you can visit www.washerbearings.com/parts get new replacement parts for your appliances.



Otherwise you can always use the Neptune Washer Back up Plan which is shown below...




Sunday, March 16, 2014

Maytag Appliance Parts 22004473 Motor Control Board - LR error code

Maytag Appliance Parts 22004473 Motor Control Board

If you open up the top section you should discover a document in there that has the wiring diagram and diagnostic tests you can run on your Neptune.
The 'LR' error code means Locked Rotor and usually shows up if the motor drive system is not following what the machine control board (MCB) is instructing it to do. The MCB instructs the motor control board how fast and how which direction to rotate the inner basket. I would also check that the belt is still on the pulleys.
Sometimes the motor control board has simply failed and does not rotate the basket or it could be that the speed sensor on the motor has quit working or has a bad connection. I will check all of the connectors in the machine and clean them by removing the connectors and reinstalling them. The sliding action will clean the connector pins if there is oxidation built up on the pins. Just make sure you install the connectors in the exact same position they were originally. When working around the motor control board which is located near the floor I would take a look at the board and see if there are any physical burnt components, leaking or bulging capacitors, etc.
After inspecting all of the connectors in the machine that you can get to I would retest the motor drive. If it does not rotate the basket and you still get the LR error code it is time to replace the motor control board. In 99% of failures the motor control board fails, not the motor. You can visit www.22004473.com for more information on the replacement motor control boards. 

Please visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal. and enter your model number and they can look up the part you need.
Please leave any comments below if this was helpful.

Saturday, March 26, 2011

Maytag Neptune Bearing 12002022 Revised Seal Install How-To

Maytag Neptune Bearing 12002022 Revised Seal Install How-To for solid door Neptune front loaders


Hi Neptuner!

I have to say that I am impressed… I asked a Neptuner to shoot his Neptune… oops, I meant shoot some video when replacing the revised lip seal on a Maytag Neptune front load washer and Jeff C. stepped up and sealed the deal!

Here is the video I put together from Jeff’s footage he shot after replacing his (MAH5500B series) Neptune bearings and 12002022 seal kit. It shows the revised lip seal installation. Jeff also purchased a new Neptune Spinner Support for his machine. If you purchase a Neptune bearing and seal kit from me and buy the new spinner support I will refund $40 when you send the 12002022 seal kit back. The new spinner support comes with a revised seal kit. This will offset your spinner support payment by $40!

If you’re not aware… The Neptune 12002022 seal kit includes 2 seals so it will work on both spinner support designs. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal. That video is here. The thicker seal is the revised lip seal.

Note: When installing the revised lip seal make sure that the ribs are towards the front bearing and the smooth section will be towards the stainless steel tub so it is not in backwards.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

Saturday, March 5, 2011

Maytag Neptune Bearing Seal Kit Install How-To

Hi Neptuner!

Here is a video I created when I was replacing Loretta's MAH4000 Maytag Neptune bearings and 12002022 seal kit. It shows the earlier lip seal installation. The 12002022 seal kit includes 2 seals so it will work on both spinner support setups. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

Saturday, April 24, 2010

Maytag Neptune 6500 burns seal

Maytag Neptune repair:

Another Neptuner needs help... Here is a question from a Neptuner that was pulled from the blogosphere...


Q: Last night, I washed some clothes with two pillows. It seems that the pillows were rubbing against the seal? (The plastic thing next to the door) and now that the seal has a hole. There is great but I will not wash until you know if that is really bad (maybe the water can get in there). Also, I think because of that the washer was making a really loud noise near the end of the cycle.

A: If the bearings are going out you can replace them. See Neptune Bearing for more info. You can also rent a special tool kit, too. Usually, the machine will start to sound like a jet taking off when in the high speed spin cycle.

If you call a tech and the bearings need attention, they will ask for $900 to replace the outer tub, unless they are a tech that owns the Neptune Bearing Tony Tool from Neptune Kits then you might get the bearings replaced for $200 or so.

It is also possible the spinner support has an issue and is causing the inner tub to wobble which can rub the plastic liner. Contact me and I can get you a new spinner support which comes with the new seal.

Until next time...