Maytag Neptune MAH4000 Spin Cycle Power Draw Via Kill A Watt Power Meter Before Tub Bearing Swap

 I was playing with a Kill A Watt power meter and a MAH4000 Maytag Neptune washer to see how much power the Neptune was drawing with an empty basket. I was trying to determine if the power draw could be an indicator that the seal and bearings have failed. This power check was before the bearing replacement…

I also performed the power draw check after the bearing replacement. Go ahead and watch the video.

 Let me know any comments or questions you have below.

 Thank you,

 Jeff Hartman

Jeff Hartman is known as “The Neptune Man” for offering Maytag Neptune washer parts to save homeowner’s Millions of dollars by repairing their own washers and dryers. See http://www.neptunewasher.com and http://www.neptunedryer.com for more appliance repair information. He now offers money saving bearing and seal kits for other makes and models at http://www.washerbearings.com.

Maytag Neptune Washer Seal Replacement - How to replace

Maytag Neptune washer seal replacement - If you notice your Maytag Neptune front load washer starting to sound like a freight train you should know that it is time... Time to replace your Maytag Neptune bearing and seal. Although, you can rent the special Neptune bearing tool kit you can replace the bearings without it. The photo above shows the Neptune bearing and a revised lip seal, o ring and installation cup. If you have the earlier lip seal you cannot install the revised lip seal because the spinner support shaft is machined different than the spinner support shaft that uses the revised lip seal. If you replace the Neptune spinner support it will come with the revised lip seal. I would recommend having a large 8 pound hammer available just in case when replacing your Neptune tub bearings... Let me know if you have any questions. Jeff Hartman

Hey Neptune Man song

OK, I have another treat for you today... Listen to my new "Hey Neptune Man" song and see if you can recognize which song it sounds like... Enjoy.




I hope you enjoyed that song!

See Neptune Washer for more information on the wax motor and bearing replacement kits.

Until next time...

How to make the Maytag Neptune bearings easier to replace

How to make the Maytag Neptune bearings easier to replace...


I just improved the Maytag washer bearing tool kit rental by adding a piece of emery cloth to it. After using the included 2” wire wheel to clean the front bearing seat area I would recommend using the emery cloth to smooth and even take down the bearing seat a smidgen. It turns out that the Neptune bearing hub is aluminum and when the rusted front bearing comes out it can distort the aluminum and make it difficult for the replacement bearing to go in. This is just one of the reasons why I recommend that the bearings be replaced as a preventative measure after the machine has reached 10 years or so. See Neptune Bearing Tip For more reasons to proactively replace the bearings and 12002022 seal.


When was your Maytag Neptune born you ask? See Neptune Born on Date



There have been situations when performing the Maytag Neptune bearing replacement where there have been ripples or ridges in the aluminum bearing seat area and these will surely stop the new bearing from fully seating or perhaps even starting in the case of a ridge on the front edge of bearing seat. I would carefully inspect the bearing seat before attempting to insert the new bearings and use the emery cloth to take them down.

The Neptune rear bearing does not have this issue in most cases because it does not get wet like the front bearing does. I’ve had extreme cases where the washer was operated for a long period of time before the bearings were replaced and the rear bearing was rusted and actually fell apart when using the tony tool to pull them out. These Neptune washer repairs are more difficult but can be corrected by using a rotary cutting tool with cutting wheels to cut a slot in the bearing race and then use a drift or chisel to knock it out. Typically, the rear still bearing looks new but you should replace it anyway.

For more information on the Maytag washer repair see Neptune Bearing Repair


Until next time…

Brick in a washing machine - Maytag Neptune Owners Don't do it!

Here is a video that some Maytag Neptune owners would like to try...




See Neptune Help and Neptune Bearing before you think about bricking your machine. Besides... this sort of activity will void your warranty :)

She's breaking up... She's breaking up! Don't worry... We can help you repair your Neptune... We have the technology. Actually, you can make your Neptune front load better than it was when it shipped from the factory!


Until next time...

MAH3000 Maytag Neptune pump question

MAH3000 Maytag Neptune pump question.

Hi. I have a Maytag Neptune washer that seems to go through the whole cycle just fine, except for the fact that the water doesn't drain out. It happened to me awhile ago and someone told me I was using too much soap. I cut down on soap and everything did work great for several months, but now it is worse than ever.

Already Tried: running the rinse cycle again, which worked in the past, but not anymore

Answer:

You have a problem with the pump, either something has gotten into it and is blocking the water flow or the pump itself is bad or the water discharge path is clogged.

See Neptune disassembly photos or videos at Neptune Help. The pump is powered from a set of timer contacts and if you rotate the timer knob you should find spots where there should be 120 VAC on the pump electrical terminals.

If the machine is full of water and you have a floor drain nearby you can lay down the drain hose and gravity will allow the water to drain from machine (unless the water path is clogged with lint or debris).

Once the water is out you can remove the pump and take the cover off of it to inspect it for any lint and debris that could keep the impeller from spinning or the motor could be bad.

To order a new pump simply enter your model number into the Appliance Parts Search box on this blog or at Neptune Help. This tool will give you exploded views and prices of all the parts in your machine and you can simply order new parts and repair your Neptune yourself and save lots of cash.

Don't forget... The MAH3000's as well as any Maytag Neptune front loader with a timer knob has the faulty door latch wax motor. If your MAH3000 serial number starts with 10 - 25 you have 2 more wax motors in the soap dispenser that should be replaced as well before they fail.

The faulty wax motors have the brownish color actuator tip.

The residential models are MAH3000, MAH4000, MAH5500A and the 2000 stackers. The digital machines do not have the wax motor issue.

You can order new wax motors from Neptune help.

Below is the new style with the black actuator tip.

Another item I can help you with is your Neptune bearings. If you notice your machine transforming into a jet engine when it starts to ramp up then it is time for new bearings and seal. If you bother the repairman they will kindly ask you for $900 which includes replacing your large outer tub. Don't do it! You can replace your bearings yourself for a lot less.

You can also rent a special tool kit that includes a step by step DVD that shows you how to do it.

See Neptune bearing for more information.

Until next time...

5 fridays 5 saturdays and 5 sundays in one month

5 fridays 5 saturdays and 5 sundays in one month


Hi Neptuner,

This is an off topic post today...

I received an email saying that the month of July 2011 has '5 fridays 5 saturdays and 5 sundays' in it and that this only occurs every 823 years?

Let's break down the calendar shall we...

Let’s think about this, a year can only start on one of seven days, so there are seven possible basic calendar years. Add leap years, and there are fourteen basic calendars. Period. And one of those calendars only gets used every 823 years? How would that be possible? It’s not of course, all fourteen calendars get cycled through regularly, in fact 2010 used the exact same calendar as 1999.

So there you have it... Yes, there will be 5 fridays 5 saturdays and 5 sundays in July 2011...

If you have a Maytag Neptune front load washer you can keep it working through all 14 possible calendars with Neptune Help and Neptune Bearing.

Whether it is the pesky defective door latch wax motor or the bearings... we can help you save money and get that pile of laundry washed.


Until next time...

Maytag Neptune Bearing - www.neptunebearing.com is now a member of the BBB

Hi Neptuner!

I wanted to let you know that I received the important BBB accreditation for my Neptune Bearing site where I offer replacement bearings and seal kits for the Maytag Neptune front load washers.

I also rent the Neptune bearing tool kit as well which includes the Neptune bearings, Maytag 12002022 seal kit, bearing spacer, wire wheel, snap ring pliers, tool kit usage, tech support and a step-by-step instructional DVD.

Neptune Help is also included with the accreditation and I will add my following other Neptune related sites as well.

By adding the BBB accreditation to my Neptune sites it means that I support the BBB's services to the public and meet their tough accreditation standards and that you can trust me to provide excellent service!

Until next time...

Paul the octopus and the Maytag Neptune Front Load Washer meet up?

I wonder if Paul the octopus can predict when your Maytag Neptune bearings are going to fail?
Oh well! The only clue you will have is that your Neptune front load washer sounds like a jet plane taking off during the high speed spin.

By the way, you can replace just your bearings and not the large outer tub and save a laundry basket full of cash. See Neptune Bearing for more information.

I also provide replacement bearings and seals for the Kenmore Elite and Whirlpool Duet front load washers as well.

Don’t forget if you have a Neptune with a timer knob (non digital) that you need to replace the door latch wax motor if it is the original one before it fails and damages your machine control board. See Neptune help for information.

2009 Chevrolet Malibu and 1959 Chevrolet Bel Air crash

Maytag Neptune repair - Off topic post for you...

Wow, which vehicle would you rather be in during a 40 mph crash... A large, heavy 1959 Chevrolet Bel Air or a 2009 Chevrolet Malibu during a crash? I know which one I would pick... Only after seeing the video!

Go ahead and check it out at 2009 Chevrolet Malibu and 1959 Chevrolet Bel Air and leave a comment on your thoughts after watching the video clip.

When your Maytag Neptune front loader crashes check out Neptune Help for repair information, genuine Maytag replacement parts. In addition, if you have the Neptune front load washer with a timer knob (non digital) you will want to replace your 12002535 door latch wax motor if you have the original one in there.

Lastly, did you know that you can replace your Neptune bearings and seal when your machine sounds like a jet plane taking off? See Neptune Bearing for more information on replacing your bearings and saving a ton of money...

Maytag Neptune Displays ND Code

Maytag Neptune Repair:


Q: My Neptune will not drain and the nd service code is in the display. what is this and how can i fix it. Thanks

A: Ahhh, the ND error code on a digital Neptune front load washer. The ND code means 'No Drain' and it is probably just something caught in the pump. I’ve seen where a coin can get in there and keep the pump from starting.

Some other items known to stop a Neptune pump: Rubber backing from a rug, rubber bands, bobbie pin, lens from a flashlight, tooth pick and a bra wire. Maybe you had something different in your pump? If so, please comment with what you discovered in your pump...

If you have a floor drain you should be able to drop the discharge hose to the floor and let gravity pull the water out so you can take the pump out and get a good look at it.

Also a word of advice to avoid wasting time. The pump is usually towards the front of the machine.

Until next time...


P.S. For all of your Neptune questions go to Maytag Neptune Repair and let's save you a service call...

P.S.S. If you notice your Neptune getting louder in the spin cycle see Neptune Bearing for information on how you can save $700 by replacing your bearings yourself and getting 5 - 10 more years out of your machine.

Maytag Neptune 6500 burns seal

Maytag Neptune repair:

Another Neptuner needs help... Here is a question from a Neptuner that was pulled from the blogosphere...


Q: Last night, I washed some clothes with two pillows. It seems that the pillows were rubbing against the seal? (The plastic thing next to the door) and now that the seal has a hole. There is great but I will not wash until you know if that is really bad (maybe the water can get in there). Also, I think because of that the washer was making a really loud noise near the end of the cycle.

A: If the bearings are going out you can replace them. See Neptune Bearing for more info. You can also rent a special tool kit, too. Usually, the machine will start to sound like a jet taking off when in the high speed spin cycle.

If you call a tech and the bearings need attention, they will ask for $900 to replace the outer tub, unless they are a tech that owns the Neptune Bearing Tony Tool from Neptune Kits then you might get the bearings replaced for $200 or so.

It is also possible the spinner support has an issue and is causing the inner tub to wobble which can rub the plastic liner. Contact me and I can get you a new spinner support which comes with the new seal.

Until next time...

Maytag Neptune MAH5500AWW Won't Unlock the Door

Here is a recent question about the Maytag Neptune front loader repair...

Q: "I have a Maytag Neptune MAH5500AWW Front Load Washer. A couple years ago I replaced the R11 & Q??, and Wax Motor (with black plunger) to fix a problem in which the spin cycle did not fully run and left the clothes wet. The washer worked without fail until last week. The current problem I am experiencing is that the washer runs through the entire wash cycle, including spin, however, the "on" light and "door lock" light stay on. Door stays locked and the washer stays in a state in which the drum sounds like it spins 1/2 turn every 15 seconds. It never turns off."

A: There are a couple of issues that can cause the wax motor to stay energized after replacing R11 resistor and Q6 triac.

The first cause could be that one of the R11 leads is no longer connected to the Q6 pins #1 and #2. If either lead of R11 becomes disconnected the wax motor will stay energized. If you have an ohmmeter, you can verify that each lead does in fact connect to either pin #1 or pin #2 of the Q6. Note: pin 1 on the Q6 triac is looking at the flat side the very left pin. Pin 2 is center pin and pin three is the far right pin when looking at the flat side. If you flip board over keep in mind the Q6 orientation.

After verifying that the R11 leads are in fact connected... The other cause could be that the Q2 and Q7 transistors need replaced. It is possible these took a 'hit' when the first R11 burnt because AC voltage can be backfed when the Q6 triac shorted out. There is a STAGE 2 kit at the Neptune Help order form where you get the Q2 and Q7 replacements.

Slightly off topic today with portable Generators

Hi Neptuners!

It seems that we rely on our homes to be energized with electricity to run all sorts of time and labor saving devices.

What happens when your power line is severed during an ice storm or a car collides with a utility pole?

I asked myself the same question and decided to be prepared. I recently purchased a propane generator. Actually, it was a Christmas gift for myself. ;-) It is a 3,500 watt model, single phase 120 VAC. I figure it will run the furnace (natural gas), fridge, freezer, sump pump and some lighting. It uses the standard grill type propane tanks and should run about 9 hours at half load.

Once I received it... I filled the oil (.6 qt.) up and hooked up the propane tank and fired it up. I was impressed with how quiet it was. How useful is a generator just sitting there? Not very... I also purchased a 30 amp, 120 VAC inlet box, 10 ft. 10-3 generator hook up cable, the Square D breaker panel generator interlock kit, 30amp 2 pole breaker, 15/15 tandom breaker, 10 ft. 10-2 w/gnd romex wire and misc. hardware.

I plan to install all of the components during my holiday break until Jan 4th! I will shoot some video for you to see like I did for the DVD duplicator I purchased last month. The DVD duplicator has produced about 50 mini DVDs, 35 CD's and so far has done a great job for me so if you need to do some CD or DVD duplication check out the DVD Duplicator site I put up.

I also put up a quick generator site you can check out, too. I love putting up websites... can't you tell!

If you would like to put up some websites I am putting together a training class to teach folks how to put up websites step-by-step. Contact me at neptunewasher@gmail.com if you're interested in putting up websites.

As always, if you have a Maytag Neptune with a timer knob... check out Neptune Help Song for a video that explains the faulty door latch wax motor issue.

Until next time...

Maytag Neptune repair - door latch wax motor

Maytag Neptune Repair


I just finished a new video that shows how to replace the door latch wax motor in the maytag neptune door latch. Here is the Neptune Wax Motor Video link.

If you have a Maytag Neptune front loader with a timer knob you will want to inspect your wax motor and make sure it has a black actuator pin. If it has the brownish color actuator pin then you will want to replace it as soon as possible.

Keep in mind that if you have a MAH3000 model with the serial number starting with a 10 thru 25 then you will have two more wax motors in the soap dispenser. These control the bleach and softener flows.

See Neptune help for more valuable Neptune front loader information.

Maytag Neptune Bearing Tony Tool - Testimonials

Maytag Neptune Bearing Tony Tool - Testimonials


Ok, I have to just pass these along... Here are a couple of Neptune owners that recently rented the Tony Tool and saved over $700 by replacing their bearings!

#1
"Just wanted you to know the tonytool worked great. Neptune washer is up and running again. Received tonytool on monday sept 28 repaired washer on tuesday sept 29 mailed tonytool back wednesday morning sept 30 by priority mail. I was considering scraping the washer before seeing your site. The bearing replacement job is nothing a person with average mechanical skills can't do. Thanks for all your help"

Curtis F.


#2
"The Tony Tool system is superb. The installation process went forward without a problem. The tool worked flawlessly. The additional tools like the snap ring pliers and wire brush were nice touches. The DVD step by step instructions made reading instructions unnecessary. Although I’d worked on old style Maytags before, the Neptune was new to me. Even so, I completed the whole job including clean-up in less than 2 hours. All the parts needed were included; nothing was overlooked. I’d definitely do business with you guys again! Thanks."

Mark Baker



As you can see the Tony Tool is the solution for your 'Out of Control' Neptune bearings... The Tony Tool is available at www.neptunekits.com along with bulk bearing and 12002022 seal kits.

Don't forget to change your 12002535 door latch wax motor when you have it apart... All of the Neptune front loaders with timer knob run the risk of damaging R11 and Q6 on the machine control board. See www.neptunehelpsong.com for the cool video that explains the issue.

Until next time...