Neptune Bearing Replacement - How To

Neptune Bearing Replacement - How To

 If you have a Maytag Neptune Front load washer there will come a time when it starts to morph into a jet plane or even a freight train..


Since you probably don't want a jet plane in your home you will want to replace your Neptune tub bearings and seal asap.

You can replace your washer bearings without the special Neptune bearing replacement tool or Tony Tool if you're handy with tools. The tool kit does save you time and effort when changing your bearings. The tool kit rental includes the tub bearings, 12002022 seal kit, bearing spacer, 2" wire wheel and step by step DVD. You can order the Maytag Neptune bearing and 12002022 Seal Kit HERE and it works on all solid door (no window) panel Neptune's. 

You can find other washer bearing and seal kits HERE.

I hope this post was helpful.

Thank you,

Jeff Hartman

P.S. For other appliance parts you can visit www.washerbearings.com/parts get new replacement parts for your appliances.

Otherwise you can always use the Neptune Washer Back up Plan which is shown below...

Maytag Appliance Parts 22004473 Motor Control Board - LR error code

Maytag Appliance Parts 22004473 Motor Control Board

If you open up the top section you should discover a document in there that has the wiring diagram and diagnostic tests you can run on your Neptune.

The 'LR' error code means Locked Rotor and usually shows up if the motor drive system is not following what the machine control board (MCB) is instructing it to do. The MCB instructs the motor control board how fast and how which direction to rotate the inner basket. I would also check that the belt is still on the pulleys.

Sometimes the motor control board has simply failed and does not rotate the basket or it could be that the speed sensor on the motor has quit working or has a bad connection. I will check all of the connectors in the machine and clean them by removing the connectors and reinstalling them. The sliding action will clean the connector pins if there is oxidation built up on the pins. Just make sure you install the connectors in the exact same position they were originally. When working around the motor control board which is located near the floor I would take a look at the board and see if there are any physical burnt components, leaking or bulging capacitors, etc.

After inspecting all of the connectors in the machine that you can get to I would retest the motor drive. If it does not rotate the basket and you still get the LR error code it is time to replace the motor control board. In 99% of failures the motor control board fails, not the motor. You can visit www.22004473.com for more information on the replacement motor control boards. 

Please visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal. and enter your model number and they can look up the part you need.

Please leave any comments below if this was helpful.

Jeff Hartman
www.neptunewasher.com
www.neptunedryer.com
www.washerbearings.com

Brody Stevens and Little Esther hangin with the Neptune Man

Here is a recent photo of me with Little Esther, Tonia, Brody Stevens. I bought a Groupon for a local show in the Columbus, Ohio area and it included a photo op. I thought... What the heck… Let’s get my photo taken with a couple of well known comedians. I will tell you more about Tonia later. She is creating a helpful website that will come in very handy for a lot of people.

Speaking of websites… If you have a washing machine… I offer special bearing and seal kits for when they start to get loud which usually indicates a tub bearing failure. I even rent a cool tool for the Maytag Neptune front load washers to help you save time and effort when replacing Neptune tub bearings. You can visit my main site at www.washerbearings.com which branches out to the different models.

Since I specialize in the tub bearing and seal kits you order the bearing and seal kits only from my sites and you can order other appliance parts by visiting www.washerbearings.com/parts to order replacement parts. Just have your model and serial numbers handy to help them look you your replacement parts.

I'm now officially called the "Neptune Man" and here is my song Vicky made for me http://neptunewasher.blogspot.com/2012/11/hey-neptune-man-song.html


Until next time…



Jeff

Maytag Neptune Bearing 12002022 Revised Seal Install How-To

Maytag Neptune Bearing 12002022 Revised Seal Install How-To for solid door Neptune front loaders


Hi Neptuner!

I have to say that I am impressed… I asked a Neptuner to shoot his Neptune… oops, I meant shoot some video when replacing the revised lip seal on a Maytag Neptune front load washer and Jeff C. stepped up and sealed the deal!

Here is the video I put together from Jeff’s footage he shot after replacing his (MAH5500B series) Neptune bearings and 12002022 seal kit. It shows the revised lip seal installation. Jeff also purchased a new Neptune Spinner Support for his machine. If you purchase a Neptune bearing and seal kit from me and buy the new spinner support I will refund $40 when you send the 12002022 seal kit back. The new spinner support comes with a revised seal kit. This will offset your spinner support payment by $40!

If you’re not aware… The Neptune 12002022 seal kit includes 2 seals so it will work on both spinner support designs. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal. That video is here. The thicker seal is the revised lip seal.

Note: When installing the revised lip seal make sure that the ribs are towards the front bearing and the smooth section will be towards the stainless steel tub so it is not in backwards.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

Maytag Neptune Bearing Seal Kit Install How-To

Hi Neptuner!

Here is a video I created when I was replacing Loretta's MAH4000 Maytag Neptune bearings and 12002022 seal kit. It shows the earlier lip seal installation. The 12002022 seal kit includes 2 seals so it will work on both spinner support setups. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

Maytag Neptune Help feedback

Hi Neptuners!

Here is feedback I received today after Chuck had changed his Neptune bearings and seal.

"Thank You Thank You Thank You I have completed the bearing replacement on my Neptune washer and all is well. It is again working like new. I have one question, my unit is a 5500BWW, do I need to replace the wax motor, or did Maytag make the change with that model #. Thanks again. Chuck S."

That's great news Chuck! Your MAH5500BWW does not have the faulty 12002535 door latch wax motor so you are OK. Jeff


If your Neptune is screaming at you while in high speed spin cycle goto http://neptunebearing.com/page4.html to purchase the replacement bearings and 12002022 seal kit.

I have a Maytag front load Neptune MAH5500BWW problem

Q: Hi. I have the MAH5500B washing machine. My wife called in a panic and said the LCD panel displayed the LR code. I read 120V ac at the receptacle. I read 120V ac at terminals 1 and 3 on connector P6 at the machine control panel. I ran the Quick Service Cycle and everything seems to function except the tub does not spin. Checking across the 10 amp fuse on the motor control board yields 1 ohm resistance. I am thinking motor but I am not sure...any ideas? 

 A: Sure. You will have to replace the Motor control board and the motor with the new Maytag 12002039 motor conversion kit which may be available on ebay https://ebay.us/Aac7zW. If you already have the newer motor control board with plastic cover, you can try just replacing your motor control board. You can look at the photos on ebay and see if they look like your motor control board.

 

It takes about an hour to install. The original motor control boards have a high failure rate on the Neptunes so Maytag decided to redesign both the motor and motor control board. 

 Have you noticed your Neptune getting loud in spin cycle? If so, then your bearings are failing and will need to be replaced. The extra friction caused by the failing bearings can cause the motor control board to shutdown and/or fail. You can get new bearings and seal kit from www.neptunebearing.com. They also rent the special Neptune bearing tool to save you lots of time and effort and the rental incudes access to a video that shows you how to teardown machine, replace bearings using tool and install the seal kit. If you ask a service technician to come over you will receive a dose of sticker shock! They will quote you over $900 to quiet your machine again...

Until next time...

Do you own a Maytag Neptune MAH8700 or MAH9700?

Have you seen the Maytag Neptune recall page? 

See http://www.washerrecall.com/ for information. Certain serial numbers are only affected and there is a box where you can enter your country, model and serial to see if your Neptune has the recall. 

The issue is a potential fire hazard if water drips onto a thermal sensor connector. Please check it out if you own a MAH8700 or a MAH9700 Neptune. 

If you own a MAH3000, MAH4000, MAH5500A or a 2000 stacker Neptune please check http://www.neptunehelp.com/ to see if your Neptune has the defective door latch wax motor which will eventually short out and damage the control board. You can proactively replace this component and prevent the control board failure.

Until next time...

door latch motor on the MAH5500BWW model

Here is a question I get often... 

"Just wondering if the door latch motor on the MAH5500BWW model was a concern and needed changed. Thanks, Doug " 

Hi Doug, you are good... Your Maytag Neptune door latch assembly was replaced with a one piece assembly and does not have the defective 12002535 wax motor in it. To see if your Neptune is affected by the defective door latch wax motor, see http://www.neptunewaxmotor.com/. 

In addition, when your Neptune starts screaming when high speed spinning it is time for bearings and a seal kit... I can save you $800 to repair your Neptune or even more if you would have decided to replace it with a new front loader set... You can also rent the famous tony tool which makes changing your bearings a snap! It even includes access to a step by step video. See http://www.neptunebearing.com/ for details.

Until next time...