Appliance Part Center - Whirlpool, Maytag, General Electric (GE) & Electrolux Parts

Appliance Part Center Please visit www.washerbearings.com/parts to order replacement parts other than tub bearings and seal.   If you own (or know someone who owns) a Maytag Neptune front load you need to check out Neptune Help to see if your machine has the defective door latch wax motor installed. 

You can prevent a $350 repair bill as well as washer down time by proactively replacing your wax motor before it fails and causes the famous no spin issue... 

Do it now! 

Until next time... 

 Jeff

MAH3000 Maytag Neptune pump question

MAH3000 Maytag Neptune pump question.

Hi. I have a Maytag Neptune washer that seems to go through the whole cycle just fine, except for the fact that the water doesn't drain out. It happened to me awhile ago and someone told me I was using too much soap. I cut down on soap and everything did work great for several months, but now it is worse than ever.

Already Tried: running the rinse cycle again, which worked in the past, but not anymore

Answer:

You have a problem with the pump, either something has gotten into it and is blocking the water flow or the pump itself is bad or the water discharge path is clogged.

See Neptune disassembly photos or videos at Neptune Help. The pump is powered from a set of timer contacts and if you rotate the timer knob you should find spots where there should be 120 VAC on the pump electrical terminals.

If the machine is full of water and you have a floor drain nearby you can lay down the drain hose and gravity will allow the water to drain from machine (unless the water path is clogged with lint or debris).

Once the water is out you can remove the pump and take the cover off of it to inspect it for any lint and debris that could keep the impeller from spinning or the motor could be bad.

To order a new pump simply enter your model number into the Appliance Parts Search box on this blog or at Neptune Help. This tool will give you exploded views and prices of all the parts in your machine and you can simply order new parts and repair your Neptune yourself and save lots of cash.

Don't forget... The MAH3000's as well as any Maytag Neptune front loader with a timer knob has the faulty door latch wax motor. If your MAH3000 serial number starts with 10 - 25 you have 2 more wax motors in the soap dispenser that should be replaced as well before they fail.

The faulty wax motors have the brownish color actuator tip.

The residential models are MAH3000, MAH4000, MAH5500A and the 2000 stackers. The digital machines do not have the wax motor issue.

You can order new wax motors from Neptune help.

Below is the new style with the black actuator tip.

Another item I can help you with is your Neptune bearings. If you notice your machine transforming into a jet engine when it starts to ramp up then it is time for new bearings and seal. If you bother the repairman they will kindly ask you for $900 which includes replacing your large outer tub. Don't do it! You can replace your bearings yourself for a lot less.

You can also rent a special tool kit that includes a step by step DVD that shows you how to do it.

See Neptune bearing for more information.

Until next time...

Maytag Neptune Bearing 12002022 Revised Seal Install How-To

Maytag Neptune Bearing 12002022 Revised Seal Install How-To for solid door Neptune front loaders


Hi Neptuner!

I have to say that I am impressed… I asked a Neptuner to shoot his Neptune… oops, I meant shoot some video when replacing the revised lip seal on a Maytag Neptune front load washer and Jeff C. stepped up and sealed the deal!

Here is the video I put together from Jeff’s footage he shot after replacing his (MAH5500B series) Neptune bearings and 12002022 seal kit. It shows the revised lip seal installation. Jeff also purchased a new Neptune Spinner Support for his machine. If you purchase a Neptune bearing and seal kit from me and buy the new spinner support I will refund $40 when you send the 12002022 seal kit back. The new spinner support comes with a revised seal kit. This will offset your spinner support payment by $40!

If you’re not aware… The Neptune 12002022 seal kit includes 2 seals so it will work on both spinner support designs. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal. That video is here. The thicker seal is the revised lip seal.

Note: When installing the revised lip seal make sure that the ribs are towards the front bearing and the smooth section will be towards the stainless steel tub so it is not in backwards.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

Maytag Neptune Bearing Seal Kit Install How-To

Hi Neptuner!

Here is a video I created when I was replacing Loretta's MAH4000 Maytag Neptune bearings and 12002022 seal kit. It shows the earlier lip seal installation. The 12002022 seal kit includes 2 seals so it will work on both spinner support setups. The thinner seal is the earlier seal and should be used if your machine had the white plastic spacer ("a" clip) between the front bearing and seal.




See Neptune Bearing for more information. I also offer the 12002533 door boot, 12002535 wax motor and the 12001788 belt at a discount when you rent the Neptune bearing tool kit.


Until next time...

MAH6700 Bearing and Seal Kit - Maytag Neptune

MAH6700 Bearing and Seal Kit - Maytag Neptune


Hi Neptuner!

Ok... I may be ahead of the curve here but I just added the MAH6700 bearing and seal kit to my Neptune Bearing order form. It will just be a matter of time before this model needs bearings and the seal replaced so you can save a ton of money by doing it yourself.

So when your Neptune MAH6700 sounds like a jet plane taking off when it enters spin cycle you should replace the bearings and seal as soon as you can so you don't cause excessive damage to the spinner support shaft.

Until next time...

5 fridays 5 saturdays and 5 sundays in one month

5 fridays 5 saturdays and 5 sundays in one month


Hi Neptuner,

This is an off topic post today...

I received an email saying that the month of July 2011 has '5 fridays 5 saturdays and 5 sundays' in it and that this only occurs every 823 years?

Let's break down the calendar shall we...

Let’s think about this, a year can only start on one of seven days, so there are seven possible basic calendar years. Add leap years, and there are fourteen basic calendars. Period. And one of those calendars only gets used every 823 years? How would that be possible? It’s not of course, all fourteen calendars get cycled through regularly, in fact 2010 used the exact same calendar as 1999.

So there you have it... Yes, there will be 5 fridays 5 saturdays and 5 sundays in July 2011...

If you have a Maytag Neptune front load washer you can keep it working through all 14 possible calendars with Neptune Help and Neptune Bearing.

Whether it is the pesky defective door latch wax motor or the bearings... we can help you save money and get that pile of laundry washed.


Until next time...

Maytag Neptune Bearing - www.neptunebearing.com is now a member of the BBB

Hi Neptuner!

I wanted to let you know that I received the important BBB accreditation for my Neptune Bearing site where I offer replacement bearings and seal kits for the Maytag Neptune front load washers.

I also rent the Neptune bearing tool kit as well which includes the Neptune bearings, Maytag 12002022 seal kit, bearing spacer, wire wheel, snap ring pliers, tool kit usage, tech support and a step-by-step instructional DVD.

Neptune Help is also included with the accreditation and I will add my following other Neptune related sites as well.

By adding the BBB accreditation to my Neptune sites it means that I support the BBB's services to the public and meet their tough accreditation standards and that you can trust me to provide excellent service!

Until next time...